Merge "dt-bindings: media: add dt bindings for sde rotator"

SDE Rotator

SDE rotator is a v4l2 rotator driver, which manages the rotator hw

block inside the Snapdragon Display Engine (or Mobile Display Subsystem)

Required properties

- compatible:		Must be "qcom,sde-rotator".

- reg:			offset and length of the register set for the device.

- reg-names:		names to refer to register sets related to this device

- interrupt-parent:	phandle for the interrupt controller that

			services interrupts for this device.

- interrupts:		Interrupt associated with rotator.

- <name>-supply:	Phandle for <name> regulator device node.

- qcom,supply-names:	names to refer to regulator device node.

- clocks:		List of Phandles for clock device nodes

			needed by the device.

- clock-names:		List of clock names needed by the device.

- #list-cells:		Number of rotator cells, must be 1

Bus Scaling Data:

- qcom,msm-bus,name:		String property describing rotator client.

- qcom,msm-bus,num-cases:	This is the the number of Bus Scaling use cases

				defined in the vectors property. This must be

				set to <3> for rotator driver where use-case 0 is

				used to take off rotator BW votes from the system.

				And use-case 1 & 2 are used in ping-pong fashion

				to generate run-time BW requests.

- qcom,msm-bus,num-paths:	This represents the number of paths in each

				Bus Scaling Usecase. This value depends on

				how many number of AXI master ports are

				dedicated to rotator for particular chipset.

- qcom,msm-bus,vectors-KBps:	* A series of 4 cell properties, with a format

				of (src, dst, ab, ib) which is defined at

				Documentation/devicetree/bindings/arm/msm/msm_bus.txt

				* Current values of src & dst are defined at

				include/linux/msm-bus-board.h

				src values allowed for rotator are:

					25 = MSM_BUS_MASTER_ROTATOR

				dst values allowed for rotator are:

					512 = MSM_BUS_SLAVE_EBI_CH0

				ab: Represents aggregated bandwidth.

				ib: Represents instantaneous bandwidth.

				* Total number of 4 cell properties will be

				(number of use-cases * number of paths).

				* These values will be overridden by the driver

				based on the run-time requirements. So initial

				ab and ib values defined here are random and

				bare no logic except for the use-case 0 where ab

				and ib values needs to be 0.

				* Define realtime vector properties followed by

				non-realtime vector properties.

Optional properties

- qcom,rot-vbif-settings: 	Array with key-value pairs of constant VBIF register

				settings used to setup MDSS QoS for optimum performance.

				The key used should be offset from "rot_vbif_phys" register

				defined in reg property.

- qcom,mdss-rot-block-size:	This integer value indicates the size of a memory block

				(in pixels) to be used by the rotator. If this property

				is not specified, then a default value of 128 pixels

				would be used.

- qcom,mdss-highest-bank-bit:	This integer value indicate tile format as opposed to usual

				linear format. The value tells the GPU highest memory

				bank bit used.

- qcom,mdss-default-ot-wr-limit: This integer value indicates maximum number of pending

				writes that can be allowed on each WR xin.

				This value can be used to reduce the pending writes

				limit and can be tuned to match performance

				requirements depending upon system state.

				Some platforms require a dynamic ot limiting in

				some cases. Setting this default ot write limit

				will enable this dynamic limiting for the write

				operations in the platforms that require these

				limits.

- qcom,mdss-default-ot-rd-limit: This integer value indicates the default number of pending

				reads that can be allowed on each RD xin.

				Some platforms require a dynamic ot limiting in

				some cases. Setting this default ot read limit

				will enable this dynamic limiting for the read

				operations in the platforms that require these

				limits.

- qcom,mdss-rot-vbif-qos-setting: This array is used to program vbif qos remapper register

				  priority for rotator clients.

- qcom,mdss-rot-vbif-memtype:	Array of u32 vbif memory type settings for each xin port.

- qcom,mdss-rot-cdp-setting:	Integer array of size two, to indicate client driven

				prefetch is available or not. Index 0 represents

				if CDP is enabled for read and index 1, if CDP

				is enabled for write operation.

- qcom,mdss-rot-qos-lut		A 4 cell property with the format of <rd_lut_0,

				rd_lut_1, wr_lut_0, wr_lut_1> indicating the qos

				lut settings for the rotator sspp and writeback

				client.

- qcom,mdss-rot-danger-lut	A two cell property with the format of <rd_lut,

				wr_lut> indicating the danger lut settings for

				the rotator sspp and writeback client.

- qcom,mdss-rot-safe-lut	A two cell property with the format of <rd_lut,

				wr_lut> indicating the safe lut settings for the

				rotator sspp and writeback client.

- qcom,mdss-inline-rot-qos-lut:	A 4 cell property with the format of <rd_lut_0,

				rd_lut_1, wr_lut_0, wr_lut_1> indicating the qos

				lut settings for the inline rotator sspp and

				writeback client.

- qcom,mdss-inline-rot-danger-lut: A two cell property with the format of

				<rd_lut, wr_lut> indicating the danger lut

				settings for the inline rotator sspp and

				writeback client.

- qcom,mdss-inline-rot-safe-lut: A two cell property with the format of

				<rd_lut, wr_lut> indicating the safe lut

				settings for the inline rotator sspp and

				writeback client.

- qcom,mdss-rot-qos-cpu-mask: A u32 value indicating desired PM QoS CPU

				affine mask.

- qcom,mdss-rot-qos-cpu-dma-latency: A u32 value indicating desired PM QoS CPU DMA

				latency in usec.

- qcom,mdss-rot-mode:		This is integer value indicates operation mode

				of the rotator device

- qcom,mdss-sbuf-headroom:	This integer value indicates stream buffer headroom in lines.

- qcom,mdss-rot-linewidth:	This integer value indicates rotator line width supported in pixels.

- cache-slice-names:		A set of names that identify the usecase names of a client that uses

				cache slice. These strings are used to look up the cache slice

				entries by name.

- cache-slices:			The tuple has phandle to llcc device as the first argument and the

				second argument is the usecase id of the client.

- qcom,sde-ubwc-malsize:	A u32 property to specify the default UBWC

				minimum allowable length configuration value.

- qcom,sde-ubwc-swizzle:	A u32 property to specify the default UBWC

				swizzle configuration value.

- qcom,rot-reg-bus:		Property to provide Bus scaling for register

				access for rotator blocks.

- power-domains:		A phandle to respective power domain node.

- qcom,mdss-rot-parent:		A 2 cell property, with format of (mdp phandle,

				instance id), of mdp device.

- qcom,mdss-rot-xin-id:		An integer array of xin-ids when nrt path for rotation

				is not available.

Subnode properties:

- compatible:		Compatible name used in smmu v2.

			smmu_v2 names should be:

			"qcom,smmu_sde_rot_unsec"- smmu context bank device for

						unsecure rotation domain.

			"qcom,smmu_sde_rot_sec"	- smmu context bank device for

						secure rotation domain.

- iommus:		specifies the SID's used by this context bank

- gdsc-mdss-supply: 	Phandle for mdss supply regulator device node.

- clocks:		List of Phandles for clock device nodes

			needed by the device.

- clock-names:		List of clock names needed by the device.

Example:

	mdss_rotator: qcom,mdss_rotator {

		compatible = "qcom,sde_rotator";

		reg = <0xfd900000 0x22100>,

			<0xfd925000 0x1000>;

		reg-names = "mdp_phys", "rot_vbif_phys";

		#list-cells = <1>;

		interrupt-parent = <&mdss_mdp>;

		interrupts = <2 0>;

		power-domains = <&mdss_mdp>;

		qcom,mdss-mdp-reg-offset = <0x00001000>;

		rot-vdd-supply = <&gdsc_mdss>;

		qcom,supply-names = "rot-vdd";

		clocks = <&clock_mmss clk_mmss_mdss_ahb_clk>,

			<&clock_mmss clk_mmss_mdss_rot_clk>;

		clock-names = "iface_clk", "rot_core_clk";

		qcom,mdss-highest-bank-bit = <0x2>;

		qcom,sde-ubwc-malsize = <0>;

		qcom,sde-ubwc-swizzle = <1>;

		/* Bus Scale Settings */

		qcom,msm-bus,name = "mdss_rotator";

		qcom,msm-bus,num-cases = <3>;

		qcom,msm-bus,num-paths = <1>;

		qcom,msm-bus,vectors-KBps =

			<25 512 0 0>,

			<25 512 0 6400000>,

			<25 512 0 6400000>;

		/* VBIF QoS remapper settings*/

		qcom,mdss-rot-vbif-qos-setting = <1 1 1 1>;

		qcom,mdss-rot-vbif-memtype = <3 3>;

		com,mdss-rot-cdp-setting = <1 1>;

		qcom,mdss-default-ot-rd-limit = <8>;

		qcom,mdss-default-ot-wr-limit = <16>;

		qcom,mdss-rot-qos-lut = <0x0 0x0 0x0 0x0>;

		qcom,mdss-rot-danger-lut = <0x0 0x0>;

		qcom,mdss-rot-safe-lut = <0x0000ffff 0x0>;

		qcom,mdss-rot-qos-cpu-mask = <0xf>;

		qcom,mdss-rot-qos-cpu-dma-latency = <75>;

		qcom,mdss-inline-rot-qos-lut = <0x0 0x0 0x00112233 0x44556677>;

		qcom,mdss-inline-rot-danger-lut = <0x0 0x0000ffff>;

		qcom,mdss-inline-rot-safe-lut = <0x0 0x0000ff00>;

		qcom,mdss-sbuf-headroom = <20>;

		cache-slice-names = "rotator";

		cache-slices = <&llcc 4>;

		rot_reg: qcom,rot-reg-bus {

			qcom,msm-bus,name = "mdss_rot_reg";

			qcom,msm-bus,num-cases = <2>;

			qcom,msm-bus,num-paths = <1>;

			qcom,msm-bus,active-only;

			qcom,msm-bus,vectors-KBps =

				<1 590 0 0>,

				<1 590 0 76800>;

		};

		smmu_rot_unsec: qcom,smmu_rot_unsec_cb {

			compatible = "qcom,smmu_sde_rot_unsec";

			iommus = <&mdp_smmu 0xe00>;

			gdsc-mdss-supply = <&gdsc_bimc_smmu>;

			clocks = <&clock_mmss clk_bimc_smmu_ahb_clk>,

				<&clock_mmss clk_bimc_smmu_axi_clk>;

			clock-names = "rot_ahb_clk", "rot_axi_clk";

		};

		smmu_sde_rot_sec: qcom,smmu_sde_rot_sec_cb {

			compatible = "qcom,smmu_sde_rot_sec";

			iommus = <&mmss_smmu 0xe01>;

			gdsc-mdss-supply = <&gdsc_bimc_smmu>;

			clocks = <&clock_mmss clk_bimc_smmu_ahb_clk>,

				<&clock_mmss clk_bimc_smmu_axi_clk>;

			clock-names = "rot_ahb_clk", "rot_axi_clk";

		};

	};