Merge "ARM: dts: msm: Add bindings for PCIe end point driver"

MSM MHI DEV

MSM MHI DEV enables communication with the host over a PCIe link using the

Modem Host Interface protocol. The driver interfaces with the IPA for

enabling the HW acceleration channel path and provides interface for

software channels to communicate between Host and device.

Required properties:

  - compatible: should be "qcom,msm-mhi-dev" for MHI device driver.

  - reg: MHI MMIO physical register space.

  - reg-names: resource names used for the MHI MMIO physical address region,

	       IPA uC command and event ring doorbell mail box address.

	       Should be "mhi_mmio_base" for MHI MMIO physical address,

	       "ipa_uc_mbox_crdb" for IPA uC Command Ring doorbell,

	       "ipa_uc_mbox_erdb" for IPA uC Event Ring doorbell passed to

	       the IPA driver.

  - qcom,mhi-ifc-id: ID of HW interface via which MHI on device side

		communicates with host side.

  - qcom,mhi-ep-msi: End point MSI number.

  - qcom,mhi-version: MHI specification version supported by the device.

Optional property:

  - qcom,use-ipa-software-channel: If property is present use IPA hardware

		accelerated path for MHI software channel data transfers

		between host and device.

  - qcom,mhi-config-iatu: If property is present map the control and data region

		between host and device using iatu.

  - qcom,mhi-interrupt: If property is present register for mhi interrupt.

  - qcom,mhi-local-pa-base: The physical base address on the device used by the

		MHI device driver to map the control and data region with the

		MHI driver on the host. This property is required if iatu

		property qcom,mhi-config-iatu is present.

  - qcom,enable-m2: If property is present M2 autonomous is enabled.

MSM MHI DEV NET

MSM MHI DEV enables communication with the host over a PCIe link using the

Network Interface.

Required properties:

  - compatible: should be "qcom,msm-mhi-dev-net" for MHI net device driver.

Optional property:

  - qcom,mhi-ethernet-interface;: If property is present use ethernet packet

	parsing support.

Example:

	mhi: qcom,msm-mhi-dev {

		compatible = "qcom,msm-mhi-dev";

		reg = <0xfc527000 0x1000>,

		     <0xfd4fa000 0x1>,

		     <0xfd4fa080 0x1>;

		reg-names = "mhi_mmio_base", "ipa_uc_mbox_crdb",

			    "ipa_uc_mbox_erdb";

		qcom,mhi-ifc-id = <0x030017cb>;

		qcom,mhi-ep-msi = <1>;

		qcom,mhi-version = <0x1000000>;

	};

	qcom,mhi_net_dev {

		compatible = "qcom,msm-mhi-dev-net";

		qcom,mhi-ethernet-interface;

	};

MSM PCI express endpoint

Required properties:

  - compatible: should be "qcom,pcie-ep".

  - reg: should contain PCIe register maps.

  - reg-names: indicates various resources passed to driver by name.

		Should be "msi", "dm_core", "elbi", "parf", "phy", "mmio",

		"tcsr_pcie_perst_en".

		These correspond to different modules within the PCIe domain.

  - #address-cells: Should provide a value of 0.

  - interrupt-parent: Should be the PCIe device node itself here.

  - interrupts: Should be in the format <0 1 2> and it is an index to the

		interrupt-map that contains PCIe related interrupts.

  - #interrupt-cells: Should provide a value of 1.

  - #interrupt-map-mask: should provide a value of 0xffffffff.

  - interrupt-map:  Must create mapping for the number of interrupts

		    that are defined in above interrupts property.

		    For PCIe device node, it should define 6 mappings for

		    the corresponding PCIe interrupts supporting the

		    specification.

  - interrupt-names: indicates interrupts passed to driver by name.

		     Should be "int_pm_turnoff", "int_dstate_change",

				"int_l1sub_timeout", "int_link_up",

				"int_link_down", "int_bridge_flush_n".

  - perst-gpio: PERST GPIO specified by PCIe spec.

  - wake-gpio: WAKE GPIO specified by PCIe spec.

  - clkreq-gpio: CLKREQ GPIO specified by PCIe spec.

  - <supply-name>-supply: phandle to the regulator device tree node.

    Refer to the schematics for the corresponding voltage regulators.

    vreg-1.8-supply: phandle to the analog supply for the PCIe controller.

    vreg-0.9-supply: phandle to the analog supply for the PCIe controller.

Optional Properties:

  - qcom,<supply-name>-voltage-level: specifies voltage levels for supply.

    Should be specified in pairs (max, min, optimal), units uV.

  - clock-names: list of names of clock inputs.

		     Should be "pcie_pipe_clk",

				"pcie_aux_clk", "pcie_cfg_ahb_clk",

				"pcie_mstr_axi_clk", "pcie_slv_axi_clk",

				"pcie_ldo";

  - max-clock-frequency-hz: list of the maximum operating frequencies stored

				in the same order of clock names;

  - resets: reset specifier pair consists of phandle for the reset controller

    and reset lines used by this controller.

  - reset-names: reset signal names sorted in the same order as the property

    of resets.

  - qcom,pcie-phy-ver: version of PCIe PHY.

  - qcom,phy-init: The initialization sequence to bring up the PCIe PHY.

    Should be specified in groups (offset, value, delay, direction).

  - qcom,phy-status-reg: Register offset for PHY status.

  - qcom,phy-status-reg2: For sdxprairie and above use only

    qcom,phy-status-reg2 as register offset for PHY status.

  - qcom,dbi-base-reg: Register offset for DBI base address.

  - qcom,slv-space-reg: Register offset for slave address space size.

  - qcom,pcie-vendor-id: Vendor id to be written to the Vendor ID register.

  - qcom,pcie-device-id: Device id to be written to the Device ID register.

  - qcom,pcie-link-speed: generation of PCIe link speed. The value could be

    1, 2 or 3.

  - qcom,pcie-active-config: boolean type; active configuration of PCIe

    addressing.

  - qcom,pcie-edma: boolean type; edma usage for PCIe.

  - qcom,pcie-aggregated-irq: boolean type; interrupts are aggregated.

  - qcom,pcie-mhi-a7-irq: boolean type; MHI a7 has separate irq.

  - qcom,pcie-perst-enum: Link enumeration will be triggered by PERST

    deassertion.

  - qcom,tcsr-not-supported: TCSR pcie perst is not supported.

  - mdm2apstatus-gpio: GPIO used by PCIe endpoint side to notify the host side.

  - Refer to "Documentation/devicetree/bindings/arm/msm/msm_bus.txt" for

    below optional properties:

	- qcom,msm-bus,name

	- qcom,msm-bus,num-cases

	- qcom,msm-bus,num-paths

	- qcom,msm-bus,vectors-KBps

  - qcom,pcie-m2-autonomous: Enable L1ss sleep/exit to support M2 autonomous mode.

  - qcom,mhi-soc-reset-offset: AXI register offset to initiate a SOC reset.

Example:

	pcie_ep: qcom,pcie@bfffd000 {

		compatible = "qcom,pcie-ep";

		reg = <0xbfffd000 0x1000>,

			<0xbfffe000 0x1000>,

			<0xbffff000 0x1000>,

			<0xfc520000 0x2000>,

			<0xfc526000 0x1000>,

			<0xfc527000 0x1000>,

			<0x01fcb000 0x1000>;

		reg-names = "msi", "dm_core", "elbi", "parf", "phy", "mmio",

				"tcsr_pcie_perst";

		#address-cells = <0>;

		interrupt-parent = <&pcie_ep>;

		interrupts = <0 1 2 3 4 5>;

		#interrupt-cells = <1>;

		interrupt-map-mask = <0xffffffff>;

		interrupt-map = <0 &intc 0 44 0

				1 &intc 0 46 0

				2 &intc 0 47 0

				3 &intc 0 50 0

				4 &intc 0 51 0

				5 &intc 0 52 0>;

		interrupt-names = "int_pm_turnoff", "int_dstate_change",

				"int_l1sub_timeout", "int_link_up",

				"int_link_down", "int_bridge_flush_n";

		perst-gpio = <&msmgpio 65 0>;

		wake-gpio = <&msmgpio 61 0>;

		clkreq-gpio = <&msmgpio 64 0>;

		mdm2apstatus-gpio = <&tlmm_pinmux 16 0>;

		gdsc-vdd-supply = <&gdsc_pcie_0>;

		vreg-1.8-supply = <&pmd9635_l8>;

		vreg-0.9-supply = <&pmd9635_l4>;

		qcom,vreg-1.8-voltage-level = <1800000 1800000 1000>;

		qcom,vreg-0.9-voltage-level = <950000 950000 24000>;

		clock-names = "pcie_pipe_clk",

				"pcie_aux_clk", "pcie_cfg_ahb_clk",

				"pcie_mstr_axi_clk", "pcie_slv_axi_clk",

				"pcie_ldo";

		max-clock-frequency-hz = <62500000>, <1000000>,

						<0>, <0>, <0>, <0>;

		resets = <&clock_gcc GCC_PCIE_BCR>,

			<&clock_gcc GCC_PCIE_PHY_BCR>;

		reset-names = "pcie_core_reset", "pcie_phy_reset";

		qcom,msm-bus,name = "pcie-ep";

		qcom,msm-bus,num-cases = <2>;

		qcom,msm-bus,num-paths = <1>;

		qcom,msm-bus,vectors-KBps =

				<45 512 0 0>,

				<45 512 500 800>;

		qcom,pcie-link-speed = <1>;

		qcom,pcie-active-config;

		qcom,pcie-aggregated-irq;

		qcom,pcie-mhi-a7-irq;

		qcom,pcie-perst-enum;

		qcom,phy-status-reg = <0x728>;

		qcom,dbi-base-reg = <0x168>;

		qcom,slv-space-reg = <0x16c>;

		qcom,phy-init = <0x604 0x03 0x0 0x1

					0x048 0x08 0x0 0x1

					0x64c 0x4d 0x0 0x1

					0x600 0x00 0x0 0x1

					0x608 0x03 0x0 0x1>;

	};