Donate to e Foundation | Murena handsets with /e/OS | Own a part of Murena! Learn more

Commit 9873964d authored by Charles Spirakis's avatar Charles Spirakis Committed by Greg Kroah-Hartman
Browse files

[PATCH] HWMON: w83791d: New hardware monitoring driver for the Winbond W83791D 



Add support for the w83791d sensor chip. The w83791d hardware is
somewhere between the w83781d and the w83792d and this driver code
is derived from the code that supports those chips.

Signed-off-by: default avatarCharles Spirakis <bezaur@gmail.com>
Signed-off-by: default avatarJean Delvare <khali@linux-fr.org>
Signed-off-by: default avatarGreg Kroah-Hartman <gregkh@suse.de>
parent 4f507ea1

Documentation/hwmon/w83791d

0 → 100644
+113 −0
Original line number Diff line number Diff line 
Kernel driver w83791d

=====================



Supported chips:

  * Winbond W83791D

    Prefix: 'w83791d'

    Addresses scanned: I2C 0x2c - 0x2f

    Datasheet: http://www.winbond-usa.com/products/winbond_products/pdfs/PCIC/W83791Da.pdf



Author: Charles Spirakis <bezaur@gmail.com>



This driver was derived from the w83781d.c and w83792d.c source files.



Credits:

  w83781d.c:

    Frodo Looijaard <frodol@dds.nl>,

    Philip Edelbrock <phil@netroedge.com>,

    and Mark Studebaker <mdsxyz123@yahoo.com>

  w83792d.c:

    Chunhao Huang <DZShen@Winbond.com.tw>,

    Rudolf Marek <r.marek@sh.cvut.cz>



Module Parameters

-----------------



* init boolean

  (default 0)

  Use 'init=1' to have the driver do extra software initializations.

  The default behavior is to do the minimum initialization possible

  and depend on the BIOS to properly setup the chip. If you know you

  have a w83791d and you're having problems, try init=1 before trying

  reset=1.



* reset boolean

  (default 0)

  Use 'reset=1' to reset the chip (via index 0x40, bit 7). The default

  behavior is no chip reset to preserve BIOS settings.



* force_subclients=bus,caddr,saddr,saddr

  This is used to force the i2c addresses for subclients of

  a certain chip. Example usage is `force_subclients=0,0x2f,0x4a,0x4b'

  to force the subclients of chip 0x2f on bus 0 to i2c addresses

  0x4a and 0x4b.





Description

-----------



This driver implements support for the Winbond W83791D chip.



Detection of the chip can sometimes be foiled because it can be in an

internal state that allows no clean access (Bank with ID register is not

currently selected). If you know the address of the chip, use a 'force'

parameter; this will put it into a more well-behaved state first.



The driver implements three temperature sensors, five fan rotation speed

sensors, and ten voltage sensors.



Temperatures are measured in degrees Celsius and measurement resolution is 1

degC for temp1 and 0.5 degC for temp2 and temp3. An alarm is triggered when

the temperature gets higher than the Overtemperature Shutdown value; it stays

on until the temperature falls below the Hysteresis value.



Fan rotation speeds are reported in RPM (rotations per minute). An alarm is

triggered if the rotation speed has dropped below a programmable limit. Fan

readings can be divided by a programmable divider (1, 2, 4, 8 for fan 1/2/3

and 1, 2, 4, 8, 16, 32, 64 or 128 for fan 4/5) to give the readings more

range or accuracy.



Voltage sensors (also known as IN sensors) report their values in millivolts.

An alarm is triggered if the voltage has crossed a programmable minimum

or maximum limit.



Alarms are provided as output from a "realtime status register". The

following bits are defined:



bit - alarm on:

0  - Vcore

1  - VINR0

2  - +3.3VIN

3  - 5VDD

4  - temp1

5  - temp2

6  - fan1

7  - fan2

8  - +12VIN

9  - -12VIN

10 - -5VIN

11 - fan3

12 - chassis

13 - temp3

14 - VINR1

15 - reserved

16 - tart1

17 - tart2

18 - tart3

19 - VSB

20 - VBAT

21 - fan4

22 - fan5

23 - reserved



When an alarm goes off, you can be warned by a beeping signal through your

computer speaker. It is possible to enable all beeping globally, or only

the beeping for some alarms.



The driver only reads the chip values each 3 seconds; reading them more

often will do no harm, but will return 'old' values.



W83791D TODO:

---------------

Provide a patch for per-file alarms as discussed on the mailing list

Provide a patch for smart-fan control (still need appropriate motherboard/fans)

drivers/hwmon/Kconfig

+10 −0
Original line number Diff line number Diff line
@@ -406,6 +406,16 @@ config SENSORS_W83781D 
	  This driver can also be built as a module.  If so, the module

	  will be called w83781d.



config SENSORS_W83791D

	tristate "Winbond W83791D"

	depends on HWMON && I2C && EXPERIMENTAL

	select HWMON_VID

	help

	  If you say yes here you get support for the Winbond W83791D chip.



	  This driver can also be built as a module.  If so, the module

	  will be called w83791d.



config SENSORS_W83792D

	tristate "Winbond W83792D"

	depends on HWMON && I2C && EXPERIMENTAL

drivers/hwmon/Makefile

+1 −0
Original line number Diff line number Diff line
@@ -10,6 +10,7 @@ obj-$(CONFIG_SENSORS_ASB100) += asb100.o 
obj-$(CONFIG_SENSORS_W83627HF)	+= w83627hf.o

obj-$(CONFIG_SENSORS_W83792D)	+= w83792d.o

obj-$(CONFIG_SENSORS_W83781D)	+= w83781d.o

obj-$(CONFIG_SENSORS_W83791D)	+= w83791d.o



obj-$(CONFIG_SENSORS_ADM1021)	+= adm1021.o

obj-$(CONFIG_SENSORS_ADM1025)	+= adm1025.o

drivers/hwmon/w83791d.c

0 → 100644
+1255 −0

File added.

Preview size limit exceeded, changes collapsed.