Donate to e Foundation | Murena handsets with /e/OS | Own a part of Murena! Learn more

Commit 825a2ff1 authored by Ben Dooks's avatar Ben Dooks Committed by Jeff Garzik
Browse files

AX88796 network driver 



Support for the Asix AX88796 network controller, an
NE2000 compatible 10/100 ethernet device with internal
PHY.

The driver supports PHY settings via either ioctl() or
the ethtool driver ops.

Signed-off-by: default avatarBen Dooks <ben-linux@fluff.org>
Signed-off-by: default avatarJeff Garzik <jeff@garzik.org>
parent f49343a5

drivers/net/8390.h

+11 −0
Original line number Original line Diff line number Diff line
@@ -73,6 +73,9 @@ struct ei_device { 
	u32 *reg_offset;		/* Register mapping table */

	u32 *reg_offset;		/* Register mapping table */

	spinlock_t page_lock;		/* Page register locks */

	spinlock_t page_lock;		/* Page register locks */

	unsigned long priv;		/* Private field to store bus IDs etc. */

	unsigned long priv;		/* Private field to store bus IDs etc. */

#ifdef AX88796_PLATFORM

	unsigned char rxcr_base;	/* default value for RXCR */

#endif

};

};





/* The maximum number of 8390 interrupt service routines called per IRQ. */

/* The maximum number of 8390 interrupt service routines called per IRQ. */
@@ -86,11 +89,19 @@ struct ei_device { 
/* Some generic ethernet register configurations. */

/* Some generic ethernet register configurations. */

#define E8390_TX_IRQ_MASK	0xa	/* For register EN0_ISR */

#define E8390_TX_IRQ_MASK	0xa	/* For register EN0_ISR */

#define E8390_RX_IRQ_MASK	0x5

#define E8390_RX_IRQ_MASK	0x5



#ifdef AX88796_PLATFORM

#define E8390_RXCONFIG		(ei_status.rxcr_base | 0x04)

#define E8390_RXOFF		(ei_status.rxcr_base | 0x20)

#else

#define E8390_RXCONFIG		0x4	/* EN0_RXCR: broadcasts, no multicast,errors */

#define E8390_RXCONFIG		0x4	/* EN0_RXCR: broadcasts, no multicast,errors */

#define E8390_RXOFF		0x20	/* EN0_RXCR: Accept no packets */

#define E8390_RXOFF		0x20	/* EN0_RXCR: Accept no packets */

#endif



#define E8390_TXCONFIG		0x00	/* EN0_TXCR: Normal transmit mode */

#define E8390_TXCONFIG		0x00	/* EN0_TXCR: Normal transmit mode */

#define E8390_TXOFF		0x02	/* EN0_TXCR: Transmitter off */

#define E8390_TXOFF		0x02	/* EN0_TXCR: Transmitter off */







/*  Register accessed at EN_CMD, the 8390 base addr.  */

/*  Register accessed at EN_CMD, the 8390 base addr.  */

#define E8390_STOP	0x01	/* Stop and reset the chip */

#define E8390_STOP	0x01	/* Stop and reset the chip */

#define E8390_START	0x02	/* Start the chip, clear reset */

#define E8390_START	0x02	/* Start the chip, clear reset */

drivers/net/Kconfig

+8 −0
Original line number Original line Diff line number Diff line
@@ -197,6 +197,14 @@ config MACB 




source "drivers/net/arm/Kconfig"

source "drivers/net/arm/Kconfig"





config AX88796

	tristate "ASIX AX88796 NE2000 clone support"

	select CRC32

	select MII

	help

	  AX88796 driver, using platform bus to provide

	  chip detection and resources



config MACE

config MACE

	tristate "MACE (Power Mac ethernet) support"

	tristate "MACE (Power Mac ethernet) support"

	depends on PPC_PMAC && PPC32

	depends on PPC_PMAC && PPC32

drivers/net/Makefile

+1 −0
Original line number Original line Diff line number Diff line
@@ -107,6 +107,7 @@ obj-$(CONFIG_NET_SB1250_MAC) += sb1250-mac.o 
obj-$(CONFIG_B44) += b44.o

obj-$(CONFIG_B44) += b44.o

obj-$(CONFIG_FORCEDETH) += forcedeth.o

obj-$(CONFIG_FORCEDETH) += forcedeth.o

obj-$(CONFIG_NE_H8300) += ne-h8300.o

obj-$(CONFIG_NE_H8300) += ne-h8300.o

obj-$(CONFIG_AX88796) += ax88796.o





obj-$(CONFIG_TSI108_ETH) += tsi108_eth.o

obj-$(CONFIG_TSI108_ETH) += tsi108_eth.o

obj-$(CONFIG_MV643XX_ETH) += mv643xx_eth.o

obj-$(CONFIG_MV643XX_ETH) += mv643xx_eth.o