ARM: dts: msm: Add tlmm pinctrl support for SA8195

Qualcomm Technologies, Inc. SDMSHRIKE TLMM block

This binding describes the Top Level Mode Multiplexer block found in the

sdmshrike platform.

- compatible:

	Usage: required

	Value type: <string>

	Definition: must be "qcom,sdmshrike-pinctrl"

- reg:

	Usage: required

	Value type: <prop-encoded-array>

	Definition: the base address and size of the north, south, west

		    and east TLMM tiles.

- reg-names:

	Usage: required

	Value type: <prop-encoded-array>

	Defintiion: names for the cells of reg, must contain "north", "south"

		    "west" and "east".

- interrupts:

	Usage: required

	Value type: <prop-encoded-array>

	Definition: should specify the TLMM summary IRQ.

- interrupt-controller:

	Usage: required

	Value type: <none>

	Definition: identifies this node as an interrupt controller

- #interrupt-cells:

	Usage: required

	Value type: <u32>

	Definition: must be 2. Specifying the pin number and flags, as defined

		    in <dt-bindings/interrupt-controller/irq.h>

- gpio-controller:

	Usage: required

	Value type: <none>

	Definition: identifies this node as a gpio controller

- #gpio-cells:

	Usage: required

	Value type: <u32>

	Definition: must be 2. Specifying the pin number and flags, as defined

		    in <dt-bindings/gpio/gpio.h>

- gpio-ranges:

	Usage: required

	Value type: <prop-encoded-array>

	Definition:  see ../gpio/gpio.txt

- gpio-reserved-ranges:

	Usage: optional

	Value type: <prop-encoded-array>

	Definition: see ../gpio/gpio.txt

Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for

a general description of GPIO and interrupt bindings.

Please refer to pinctrl-bindings.txt in this directory for details of the

common pinctrl bindings used by client devices, including the meaning of the

phrase "pin configuration node".

The pin configuration nodes act as a container for an arbitrary number of

subnodes. Each of these subnodes represents some desired configuration for a

pin, a group, or a list of pins or groups. This configuration can include the

mux function to select on those pin(s)/group(s), and various pin configuration

parameters, such as pull-up, drive strength, etc.

PIN CONFIGURATION NODES:

The name of each subnode is not important; all subnodes should be enumerated

and processed purely based on their content.

Each subnode only affects those parameters that are explicitly listed. In

other words, a subnode that lists a mux function but no pin configuration

parameters implies no information about any pin configuration parameters.

Similarly, a pin subnode that describes a pullup parameter implies no

information about e.g. the mux function.

The following generic properties as defined in pinctrl-bindings.txt are valid

to specify in a pin configuration subnode:

- pins:

	Usage: required

	Value type: <string-array>

	Definition: List of gpio pins affected by the properties specified in

		    this subnode.

		    Valid pins are:

		      gpio0-gpio149

		        Supports mux, bias and drive-strength

		      sdc1_clk, sdc1_cmd, sdc1_data sdc2_clk, sdc2_cmd,

		      sdc2_data sdc1_rclk

		        Supports bias and drive-strength

		      ufs_reset

		        Supports bias and drive-strength

- function:

	Usage: required

	Value type: <string>

	Definition: Specify the alternative function to be configured for the

		    specified pins. Functions are only valid for gpio pins.

		    Valid values are:

		    adsp_ext, agera_pll, aoss_cti, ddr_pxi2, atest_char,

		    atest_char0, atest_char1, atest_char2, atest_char3,

		    audio_ref, atest_usb1, atest_usb2, atest_usb10,

		    atest_usb11, atest_usb12, atest_usb13, atest_usb20,

		    atest_usb21, atest_usb22, atest_usb2, atest_usb23,

		    btfm_slimbus, cam_mclk, cci_async, cci_i2c, cci_timer0,

		    cci_timer1, cci_timer2, cci_timer3, cci_timer4,

		    cri_trng, cri_trng0, cri_trng1, dbg_out, ddr_bist,

		    ddr_pxi0, ddr_pxi1, ddr_pxi3, edp_hot, edp_lcd,

		    emac_phy, emac_pps, gcc_gp1, gcc_gp2, gcc_gp3, gpio,

		    hs1_mi2s, hs2_mi2s, hs3_mi2s, jitter_bist,

		    lpass_slimbus, mdp_vsync, mdp_vsync0, mdp_vsync1,

		    mdp_vsync2, mdp_vsync3, mss_lte, m_voc, nav_pps,

		    pa_indicator, pci_e0, phase_flag, pll_bypassnl,

		    pll_bist, pci_e1, pll_reset, pri_mi2s, pri_mi2s_ws,

		    prng_rosc, qdss, qdss_cti, qlink_request, qlink_enable,

		    qspi0, qspi1, qspi2, qspi3, qspi_clk, qspi_cs, qua_mi2s,

		    qup0, qup1, qup2, qup3, qup4, qup5, qup6, qup7, qup8,

		    qup9, qup10, qup11, qup12, qup13, qup14, qup15, qup16,

		    qup17, qup18, qup19, qup_l4, qup_l5, qup_l6, rgmii,

		    sdc4, sd_write, sec_mi2s, spkr_i2s, sp_cmu, ter_mi2s,

		    tgu_ch0, tgu_ch1, tgu_ch2, tgu_ch3, tsense_pwm1,

		    tsense_pwm2, tsif1, tsif2, uim1, uim2, uim_batt,

		    usb2phy_ac, usb_phy, vfr_1, vsense_trigger, wlan1_adc0,

		    wlan1_adc1, wlan2_adc0, wlan2_adc1, wmss_reset

- bias-disable:

	Usage: optional

	Value type: <none>

	Definition: The specified pins should be configured as no pull.

- bias-pull-down:

	Usage: optional

	Value type: <none>

	Definition: The specified pins should be configured as pull down.

- bias-pull-up:

	Usage: optional

	Value type: <none>

	Definition: The specified pins should be configured as pull up.

- output-high:

	Usage: optional

	Value type: <none>

	Definition: The specified pins are configured in output mode, driven

		    high.

		    Not valid for sdc pins.

- output-low:

	Usage: optional

	Value type: <none>

	Definition: The specified pins are configured in output mode, driven

		    low.

		    Not valid for sdc pins.

- drive-strength:

	Usage: optional

	Value type: <u32>

	Definition: Selects the drive strength for the specified pins, in mA.

		    Valid values are: 2, 4, 6, 8, 10, 12, 14 and 16

Example:

        tlmm: pinctrl@3000000 {

                compatible = "qcom,sdmshrike-pinctrl";

                reg = <0x03000000 0xddc000>, <0x17c000f0 0x60>;

                reg-names = "pinctrl", "spi_cfg";

                interrupts = <0 208 0>;

                gpio-controller;

                #gpio-cells = <2>;

                interrupt-controller;

                #interrupt-cells = <2>;

	};

};

#include "sdmshrike-pinctrl.dtsi"