dt-bindings: msm: vidc: Clean-up dt properties

=====

Required properties:

- compatible : one of:

	- "qcom,msm-vidc"

	- "qcom,lahaina-vidc" : Invokes driver-specific data for LAHAINA.

	- "msm-vidc"

	- "lahaina-vidc" : Invokes driver-specific data for LAHAINA.

Optional properties:

- reg : offset and length of the register set for the device.

- sku-index : sku version of the hardware.

- interrupts : should contain the vidc interrupt.

- qcom,reg-presets : list of offset-value pairs for registers to be written.

- vidc,reg-presets : list of offset-value-mask trios for registers to be written.

	The offsets are from the base offset specified in 'reg'. This is mainly

	used for QoS, VBIF, etc. presets for video.

- qcom,qdss-presets : list of physical address and memory allocation size pairs.

	used for QoS, VBIF, etc. presets for video. The mask specifies which bits

	of the register to update

- vidc,qdss-presets : list of physical address and memory allocation size pairs.

	when fw_debug_mode is set as HFI_DEBUG_MODE_QDSS, all firmware messages will be

	written to QDSS memory.

- *-supply: A phandle pointing to the appropriate regulator. Number of

- clock-names: an array of clocks that the driver is supposed to be

	manipulating. The clocks names here correspond to the clock names used in

	clk_get(<name>).

- qcom,proxy-clock-names:

- qcom,clock-configs = an array of bitmaps of clocks' configurations. The index

	of the bitmap corresponds to the clock at the same index in qcom,clock-names.

- vidc,proxy-clock-names:

- vidc,clock-configs = an array of bitmaps of clocks' configurations. The index

	of the bitmap corresponds to the clock at the same index in vidc,clock-names.

	The bitmaps describes the actions that the device needs to take regarding the

	clock (i.e. scale it based on load).

	The bitmap is defined as:

	scalable = 0x1 (if the driver should vary the clock's frequency based on load)

- qcom,allowed-clock-rates = an array of supported clock rates by the chipset.

- qcom,clock-freq-tbl = node containing individual domain nodes, each with:

	- qcom,codec-mask: a bitmap of supported codec types, every two bits

- vidc,allowed-clock-rates = an array of supported clock rates by the chipset.

- vidc,clock-freq-tbl = node containing individual domain nodes, each with:

	- vidc,codec-mask: a bitmap of supported codec types, every two bits

		represents a codec type.

		supports mvc encoder = 0x00000001

		supports mvc decoder = 0x00000003

		supports vp8 decoder = 0x03000000

		supports hevc encoder = 0x04000000

		supports hevc decoder = 0x0c000000

	- qcom,cycles-per-mb: number of cycles required to process each macro

	- vidc,cycles-per-mb: number of cycles required to process each macro

		block.

	- qcom,low-power-cycles-per-mb: number of cycles required to process each

	- vidc,low-power-cycles-per-mb: number of cycles required to process each

		macro block in low power mode.

		the required frequency to get the final frequency, the factor is

		represented in Q16 format.

	signal that affects the device, or that the device manages.

- reset-names: List of reset signal name strings sorted in the same order as

	the resets property.

- qcom,vidc-iommu-domains = node containing individual domain nodes, each with:

		- a unique domain name for the domain node (e.g vidc,domain-ns)

		- qcom,vidc-domain-phandle: phandle for the domain as defined in

		 <target>-iommu-domains.dtsi (e.g msm8974-v1-iommu-domains.dtsi)

		- qcom,vidc-buffer-types: bitmap of buffer types that can be mapped into each

		 IOMMU domain.

		 - Buffer types are defined as the following:

			input = 0x1

			output = 0x2

			output2 = 0x4

			extradata input = 0x8

			extradata output = 0x10

			extradata output2 = 0x20

			internal scratch = 0x40

			internal scratch1 = 0x80

			internal scratch2 = 0x100

			internal persist = 0x200

			internal persist1 = 0x400

			internal cmd queue = 0x800

- cache-slice-names = An array of supported cache slice names by llcc

- cache-slices = An array of supported cache slice ids corresponding

	to cache-slice-names by llcc

- interconnect-names : List of interconnect path name strings sorted in the same

	order as the interconnects property. Driver will use interconnect-names to match

	interconnect paths with interconnect specifier pairs.

- qcom,bus-range-kbps : An array of ranges (<min max>) that indicate the

- vidc,bus-range-kbps : An array of ranges (<min max>) that indicate the

	minimum and maximum acceptable votes for the bus.

	In the absence of this property, <0 INT_MAX> is used.

=============

Required properties:

- compatible : one of:

	- "qcom,msm-vidc,context-bank"

	- "msm-vidc-context-bank"

- iommus : A phandle parsed by smmu driver. Number of entries will vary

	across targets.

- qcom,secure-context-bank : bool indicating secure context bank.

Memory Heaps

============

Required properties:

- compatible : one of:

	- "qcom,msm-vidc,mem-adsp"

	- "qcom,msm-vidc,mem-cdsp"

- memory-region : phandle to the memory heap/region.

Example:

	qcom,vidc@fdc00000 {

		compatible = "qcom,msm-vidc";

	vidc@aa00000 {

		compatible = "msm-vidc";

		reg = <0xfdc00000 0xff000>;

		interrupts = <0 44 0>;

		venus-supply = <&gdsc>;

		venus-core0-supply = <&gdsc1>;

		venus-core1-supply = <&gdsc2>;

		qcom,reg-presets = <0x80004 0x1>,

		vidc,reg-presets = <0x80004 0x1>,

			<0x80178 0x00001FFF>;

		qcom,qdss-presets = <0xFC307000 0x1000>,

		vidc,qdss-presets = <0xFC307000 0x1000>,

			<0xFC322000 0x1000>;

		clock-names = "foo_clk", "bar_clk", "baz_clk";

		qcom,clock-configs = <0x3 0x1 0x0>;

		qcom,buffer-type-tz-usage-table = <0x1 0x1>,

						<0x1fe 0x2>;

		qcom,allowed-clock-rates = <200000000 300000000 400000000>;

		vidc,clock-configs = <0x3 0x1 0x0>;

		vidc,allowed-clock-rates = <200000000 300000000 400000000>;

		/* Bus Interconnects */

		interconnect-names = "venus-cnoc", "venus-ddr", "venus-llcc";

				<&mmss_noc MASTER_VIDEO_P0

					&gem_noc SLAVE_LLCC>;

		/* Bus BW range (low, high) for each bus */

		qcom,bus-range-kbps = <1000 1000

		vidc,bus-range-kbps = <1000 1000

					1000 15000000

					1000 15000000>;

		non_secure_cb {

			compatible = "qcom,msm-vidc,context-bank";

			compatible = "msm-vidc-context-bank";

			label = "venus_ns";

			iommus =

				<&apps_smmu 0x1300 0x60>;