Merge "regulator: rpm-smd-regulator: Add support for proxy consumers" (25339ae9) · Commits · e / devices / android_kernel_fairphone_FP5

drivers/regulator/Kconfig

+11 −0

Original line number	Diff line number	Diff line
		@@ -1181,6 +1181,17 @@ config REGULATOR_RPMH
		control allows for voting on regulator state between multiple
		processors within the SoC.

		config REGULATOR_RPM_SMD
		tristate "RPM SMD regulator driver"
		depends on OF
		depends on MSM_RPM_SMD
		help
		Compile in support for the RPM SMD regulator driver which is used for
		setting voltages and other parameters of the various power rails
		supplied by some Qualcomm Technologies Inc. PMICs. The RPM SMD regulator driver should
		be used on systems which contain an RPM which communicates with the
		application processor over SMD.

		config REGULATOR_STUB
		tristate "Stub Regulator"
		help

drivers/regulator/Makefile

+1 −0

Original line number	Diff line number	Diff line
		@@ -87,6 +87,7 @@ obj-$(CONFIG_REGULATOR_QCOM_PM8008) += qcom_pm8008-regulator.o
		obj-$(CONFIG_REGULATOR_QCOM_RPM) += qcom_rpm-regulator.o
		obj-$(CONFIG_REGULATOR_QCOM_RPMH) += qcom-rpmh-regulator.o
		obj-$(CONFIG_REGULATOR_QCOM_SMD_RPM) += qcom_smd-regulator.o
		obj-$(CONFIG_REGULATOR_RPM_SMD) += rpm-smd-regulator.o
		obj-$(CONFIG_REGULATOR_QCOM_SPMI) += qcom_spmi-regulator.o
		obj-$(CONFIG_REGULATOR_QPNP_LCDB) += qpnp-lcdb-regulator.o
		obj-$(CONFIG_REGULATOR_QPNP_AMOLED) += qpnp-amoled-regulator.o

drivers/regulator/rpm-smd-regulator.c

0 → 100644

+1795 −0

File added.

Preview size limit exceeded, changes collapsed.

include/linux/regulator/rpm-smd-regulator.h

0 → 100644

+95 −0

Original line number	Diff line number	Diff line
		/* SPDX-License-Identifier: GPL-2.0-only */
		/*
		* Copyright (c) 2012-2013, 2015, 2017, 2019-2020, The Linux Foundation. All rights reserved.
		*/

		#ifndef _LINUX_REGULATOR_RPM_SMD_H
		#define _LINUX_REGULATOR_RPM_SMD_H

		#include <linux/device.h>

		struct rpm_regulator;

		/**
		* enum rpm_regulator_voltage_corner - possible voltage corner values
		*
		* These should be used in regulator_set_voltage() and
		* rpm_regulator_set_voltage() calls for corner type regulators as if they had
		* units of uV.
		*
		* Note, the meaning of corner values is set by the RPM. It is possible that
		* future platforms will utilize different corner values. The values specified
		* in this enum correspond to MSM8974 for PMIC PM8841 SMPS 2 (VDD_Dig).
		*/
		enum rpm_regulator_voltage_corner {
		RPM_REGULATOR_CORNER_NONE = 1,
		RPM_REGULATOR_CORNER_RETENTION,
		RPM_REGULATOR_CORNER_SVS_KRAIT,
		RPM_REGULATOR_CORNER_SVS_SOC,
		RPM_REGULATOR_CORNER_NORMAL,
		RPM_REGULATOR_CORNER_TURBO,
		RPM_REGULATOR_CORNER_SUPER_TURBO,
		};

		/**
		* enum rpm_regulator_voltage_level - possible voltage level values
		*
		* These should be used in regulator_set_voltage() and
		* rpm_regulator_set_voltage() calls for level type regulators as if they had
		* units of uV.
		*
		* Note: the meaning of level values is set by the RPM.
		*/
		enum rpm_regulator_voltage_level {
		RPM_REGULATOR_LEVEL_NONE = 0,
		RPM_REGULATOR_LEVEL_RETENTION = 16,
		RPM_REGULATOR_LEVEL_RETENTION_PLUS = 32,
		RPM_REGULATOR_LEVEL_MIN_SVS = 48,
		RPM_REGULATOR_LEVEL_LOW_SVS = 64,
		RPM_REGULATOR_LEVEL_SVS = 128,
		RPM_REGULATOR_LEVEL_SVS_PLUS = 192,
		RPM_REGULATOR_LEVEL_NOM = 256,
		RPM_REGULATOR_LEVEL_NOM_PLUS = 320,
		RPM_REGULATOR_LEVEL_TURBO = 384,
		RPM_REGULATOR_LEVEL_TURBO_NO_CPR = 416,
		RPM_REGULATOR_LEVEL_BINNING = 512,
		RPM_REGULATOR_LEVEL_MAX = 65535,
		};

		/**
		* enum rpm_regulator_mode - control mode for LDO or SMPS type regulators
		* %RPM_REGULATOR_MODE_AUTO: For SMPS type regulators, use SMPS auto mode so
		* that the hardware can automatically switch
		* between PFM and PWM modes based on realtime
		* load.
		* LDO type regulators do not support this mode.
		* %RPM_REGULATOR_MODE_IPEAK: For SMPS type regulators, use aggregated
		* software current requests to determine
		* usage of PFM or PWM mode.
		* For LDO type regulators, use aggregated
		* software current requests to determine
		* usage of LPM or HPM mode.
		* %RPM_REGULATOR_MODE_HPM: For SMPS type regulators, force the
		* usage of PWM mode.
		* For LDO type regulators, force the
		* usage of HPM mode.
		*
		* These values should be used in calls to rpm_regulator_set_mode().
		*/
		enum rpm_regulator_mode {
		RPM_REGULATOR_MODE_AUTO,
		RPM_REGULATOR_MODE_IPEAK,
		RPM_REGULATOR_MODE_HPM,
		};

		#ifdef CONFIG_DEBUG_FS

		static void rpm_vreg_create_debugfs(struct rpm_regulator *reg);

		#else

		static inline void rpm_vreg_create_debugfs(struct rpm_regulator *reg)
		{
		}
		#endif
		#endif