ARM: dts: vf610-zii-dev: Add .dts file for rev. C (d4cd1581) · Commits · e / devices / android_kernel_fairphone_FP4

arch/arm/boot/dts/Makefile

+2 −1

Original line number	Diff line number	Diff line
		@@ -463,7 +463,8 @@ dtb-$(CONFIG_SOC_VF610) += \
		vf610-cosmic.dtb \
		vf610m4-cosmic.dtb \
		vf610-twr.dtb \
		vf610-zii-dev-rev-b.dtb
		vf610-zii-dev-rev-b.dtb \
		vf610-zii-dev-rev-c.dtb
		dtb-$(CONFIG_ARCH_MXS) += \
		imx23-evk.dtb \
		imx23-olinuxino.dtb \

arch/arm/boot/dts/vf610-zii-dev-rev-b.dts

+14 −301

Original line number	Diff line number	Diff line
		@@ -43,32 +43,12 @@
		*/

		/dts-v1/;
		#include "vf610.dtsi"
		#include "vf610-zii-dev.dtsi"

		/ {
		model = "ZII VF610 Development Board, Rev B";
		compatible = "zii,vf610dev-b", "zii,vf610dev", "fsl,vf610";

		chosen {
		stdout-path = "serial0:115200n8";
		};

		memory {
		reg = <0x80000000 0x20000000>;
		};

		gpio-leds {
		compatible = "gpio-leds";
		pinctrl-0 = <&pinctrl_leds_debug>;
		pinctrl-names = "default";

		debug {
		label = "zii:green:debug1";
		gpios = <&gpio2 10 GPIO_ACTIVE_HIGH>;
		linux,default-trigger = "heartbeat";
		};
		};

		mdio-mux {
		compatible = "mdio-mux-gpio";
		pinctrl-0 = <&pinctrl_mdio_mux>;
		@@ -86,7 +66,7 @@
		#address-cells = <1>;
		#size-cells = <0>;

		switch0: switch0@0 {
		switch0: switch@0 {
		compatible = "marvell,mv88e6085";
		pinctrl-0 = <&pinctrl_gpio_switch0>;
		pinctrl-names = "default";
		@@ -102,6 +82,7 @@
		ports {
		#address-cells = <1>;
		#size-cells = <0>;

		port@0 {
		reg = <0>;
		label = "lan0";
		@@ -136,6 +117,7 @@
		reg = <6>;
		label = "cpu";
		ethernet = <&fec1>;

		fixed-link {
		speed = <100>;
		full-duplex;
		@@ -168,7 +150,7 @@
		#address-cells = <1>;
		#size-cells = <0>;

		switch1: switch1@0 {
		switch1: switch@0 {
		compatible = "marvell,mv88e6085";
		pinctrl-0 = <&pinctrl_gpio_switch1>;
		pinctrl-names = "default";
		@@ -184,6 +166,7 @@
		ports {
		#address-cells = <1>;
		#size-cells = <0>;

		port@0 {
		reg = <0>;
		label = "lan3";
		@@ -207,6 +190,7 @@
		label = "dsa";
		link = <&switch2port9>;
		phy-mode = "rgmii-txid";

		fixed-link {
		speed = <1000>;
		full-duplex;
		@@ -227,16 +211,19 @@
		mdio {
		#address-cells = <1>;
		#size-cells = <0>;

		switch1phy0: switch1phy0@0 {
		reg = <0>;
		interrupt-parent = <&switch1>;
		interrupts = <0 IRQ_TYPE_LEVEL_HIGH>;
		};

		switch1phy1: switch1phy0@1 {
		reg = <1>;
		interrupt-parent = <&switch1>;
		interrupts = <1 IRQ_TYPE_LEVEL_HIGH>;
		};

		switch1phy2: switch1phy0@2 {
		reg = <2>;
		interrupt-parent = <&switch1>;
		@@ -261,6 +248,7 @@
		ports {
		#address-cells = <1>;
		#size-cells = <0>;

		port@0 {
		reg = <0>;
		label = "lan6";
		@@ -279,6 +267,7 @@
		port@3 {
		reg = <3>;
		label = "optical3";

		fixed-link {
		speed = <1000>;
		full-duplex;
		@@ -290,6 +279,7 @@
		port@4 {
		reg = <4>;
		label = "optical4";

		fixed-link {
		speed = <1000>;
		full-duplex;
		@@ -304,6 +294,7 @@
		phy-mode = "rgmii-txid";
		link = <&switch1port5
		&switch0port5>;

		fixed-link {
		speed = <1000>;
		full-duplex;
		@@ -320,25 +311,6 @@
		};
		};

		reg_vcc_3v3_mcu: regulator-vcc-3v3-mcu {
		compatible = "regulator-fixed";
		regulator-name = "vcc_3v3_mcu";
		regulator-min-microvolt = <3300000>;
		regulator-max-microvolt = <3300000>;
		};

		usb0_vbus: regulator-usb0-vbus {
		compatible = "regulator-fixed";
		pinctrl-0 = <&pinctrl_usb_vbus>;
		regulator-name = "usb_vbus";
		regulator-min-microvolt = <5000000>;
		regulator-max-microvolt = <5000000>;
		enable-active-high;
		regulator-always-on;
		regulator-boot-on;
		gpio = <&gpio0 6 0>;
		};

		spi0 {
		compatible = "spi-gpio";
		pinctrl-0 = <&pinctrl_gpio_spi0>;
		@@ -375,49 +347,6 @@
		};
		};

		&adc0 {
		pinctrl-names = "default";
		pinctrl-0 = <&pinctrl_adc0_ad5>;
		vref-supply = <&reg_vcc_3v3_mcu>;
		status = "okay";
		};

		&edma0 {
		status = "okay";
		};

		&esdhc1 {
		pinctrl-names = "default";
		pinctrl-0 = <&pinctrl_esdhc1>;
		bus-width = <4>;
		status = "okay";
		};

		&fec0 {
		phy-mode = "rmii";
		pinctrl-names = "default";
		pinctrl-0 = <&pinctrl_fec0>;
		status = "okay";
		};

		&fec1 {
		phy-mode = "rmii";
		pinctrl-names = "default";
		pinctrl-0 = <&pinctrl_fec1>;
		status = "okay";

		fixed-link {
		speed = <100>;
		full-duplex;
		};

		mdio1: mdio {
		#address-cells = <1>;
		#size-cells = <0>;
		status = "okay";
		};
		};

		&i2c0 {
		clock-frequency = <100000>;
		pinctrl-names = "default";
		@@ -442,33 +371,6 @@
		interrupt-parent = <&gpio2>;
		interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
		};

		lm75@48 {
		compatible = "national,lm75";
		reg = <0x48>;
		};

		at24c04@50 {
		compatible = "atmel,24c04";
		reg = <0x50>;
		};

		at24c04@52 {
		compatible = "atmel,24c04";
		reg = <0x52>;
		};

		ds1682@6b {
		compatible = "dallas,ds1682";
		reg = <0x6b>;
		};
		};

		&i2c1 {
		clock-frequency = <100000>;
		pinctrl-names = "default";
		pinctrl-0 = <&pinctrl_i2c1>;
		status = "okay";
		};

		&i2c2 {
		@@ -538,120 +440,8 @@
		};
		};

		&uart0 {
		pinctrl-names = "default";
		pinctrl-0 = <&pinctrl_uart0>;
		status = "okay";
		};

		&uart1 {
		pinctrl-names = "default";
		pinctrl-0 = <&pinctrl_uart1>;
		status = "okay";
		};

		&uart2 {
		pinctrl-names = "default";
		pinctrl-0 = <&pinctrl_uart2>;
		status = "okay";
		};

		&usbdev0 {
		disable-over-current;
		vbus-supply = <&usb0_vbus>;
		dr_mode = "host";
		status = "okay";
		};

		&usbh1 {
		disable-over-current;
		status = "okay";
		};

		&usbmisc0 {
		status = "okay";
		};

		&usbmisc1 {
		status = "okay";
		};

		&usbphy0 {
		status = "okay";
		};

		&usbphy1 {
		status = "okay";
		};

		&iomuxc {
		pinctrl_adc0_ad5: adc0ad5grp {
		fsl,pins = <
		VF610_PAD_PTC30__ADC0_SE5 0x00a1
		>;
		};

		pinctrl_dspi0: dspi0grp {
		fsl,pins = <
		VF610_PAD_PTB18__DSPI0_CS1 0x1182
		VF610_PAD_PTB19__DSPI0_CS0 0x1182
		VF610_PAD_PTB20__DSPI0_SIN 0x1181
		VF610_PAD_PTB21__DSPI0_SOUT 0x1182
		VF610_PAD_PTB22__DSPI0_SCK 0x1182
		>;
		};

		pinctrl_dspi2: dspi2grp {
		fsl,pins = <
		VF610_PAD_PTD31__DSPI2_CS1 0x1182
		VF610_PAD_PTD30__DSPI2_CS0 0x1182
		VF610_PAD_PTD29__DSPI2_SIN 0x1181
		VF610_PAD_PTD28__DSPI2_SOUT 0x1182
		VF610_PAD_PTD27__DSPI2_SCK 0x1182
		>;
		};

		pinctrl_esdhc1: esdhc1grp {
		fsl,pins = <
		VF610_PAD_PTA24__ESDHC1_CLK 0x31ef
		VF610_PAD_PTA25__ESDHC1_CMD 0x31ef
		VF610_PAD_PTA26__ESDHC1_DAT0 0x31ef
		VF610_PAD_PTA27__ESDHC1_DAT1 0x31ef
		VF610_PAD_PTA28__ESDHC1_DATA2 0x31ef
		VF610_PAD_PTA29__ESDHC1_DAT3 0x31ef
		VF610_PAD_PTA7__GPIO_134 0x219d
		>;
		};

		pinctrl_fec0: fec0grp {
		fsl,pins = <
		VF610_PAD_PTC0__ENET_RMII0_MDC 0x30d2
		VF610_PAD_PTC1__ENET_RMII0_MDIO 0x30d3
		VF610_PAD_PTC2__ENET_RMII0_CRS 0x30d1
		VF610_PAD_PTC3__ENET_RMII0_RXD1 0x30d1
		VF610_PAD_PTC4__ENET_RMII0_RXD0 0x30d1
		VF610_PAD_PTC5__ENET_RMII0_RXER 0x30d1
		VF610_PAD_PTC6__ENET_RMII0_TXD1 0x30d2
		VF610_PAD_PTC7__ENET_RMII0_TXD0 0x30d2
		VF610_PAD_PTC8__ENET_RMII0_TXEN 0x30d2
		>;
		};

		pinctrl_fec1: fec1grp {
		fsl,pins = <
		VF610_PAD_PTA6__RMII_CLKIN 0x30d1
		VF610_PAD_PTC9__ENET_RMII1_MDC 0x30d2
		VF610_PAD_PTC10__ENET_RMII1_MDIO 0x30d3
		VF610_PAD_PTC11__ENET_RMII1_CRS 0x30d1
		VF610_PAD_PTC12__ENET_RMII1_RXD1 0x30d1
		VF610_PAD_PTC13__ENET_RMII1_RXD0 0x30d1
		VF610_PAD_PTC14__ENET_RMII1_RXER 0x30d1
		VF610_PAD_PTC15__ENET_RMII1_TXD1 0x30d2
		VF610_PAD_PTC16__ENET_RMII1_TXD0 0x30d2
		VF610_PAD_PTC17__ENET_RMII1_TXEN 0x30d2
		>;
		};

		pinctrl_gpio_e6185_eeprom_sel: pinctrl-gpio-e6185-eeprom-spi0 {
		fsl,pins = <
		VF610_PAD_PTE27__GPIO_132 0x33e2
		@@ -680,39 +470,6 @@
		>;
		};

		pinctrl_i2c_mux_reset: pinctrl-i2c-mux-reset {
		fsl,pins = <
		VF610_PAD_PTE14__GPIO_119 0x31c2
		>;
		};

		pinctrl_i2c0: i2c0grp {
		fsl,pins = <
		VF610_PAD_PTB14__I2C0_SCL 0x37ff
		VF610_PAD_PTB15__I2C0_SDA 0x37ff
		>;
		};

		pinctrl_i2c1: i2c1grp {
		fsl,pins = <
		VF610_PAD_PTB16__I2C1_SCL 0x37ff
		VF610_PAD_PTB17__I2C1_SDA 0x37ff
		>;
		};

		pinctrl_i2c2: i2c2grp {
		fsl,pins = <
		VF610_PAD_PTA22__I2C2_SCL 0x37ff
		VF610_PAD_PTA23__I2C2_SDA 0x37ff
		>;
		};

		pinctrl_leds_debug: pinctrl-leds-debug {
		fsl,pins = <
		VF610_PAD_PTD20__GPIO_74 0x31c2
		>;
		};

		pinctrl_mdio_mux: pinctrl-mdio-mux {
		fsl,pins = <
		VF610_PAD_PTA18__GPIO_8 0x31c2
		@@ -727,48 +484,4 @@
		VF610_PAD_PTB28__GPIO_98 0x219d
		>;
		};

		pinctrl_qspi0: qspi0grp {
		fsl,pins = <
		VF610_PAD_PTD7__QSPI0_B_QSCK 0x31c3
		VF610_PAD_PTD8__QSPI0_B_CS0 0x31ff
		VF610_PAD_PTD9__QSPI0_B_DATA3 0x31c3
		VF610_PAD_PTD10__QSPI0_B_DATA2 0x31c3
		VF610_PAD_PTD11__QSPI0_B_DATA1 0x31c3
		VF610_PAD_PTD12__QSPI0_B_DATA0 0x31c3
		>;
		};

		pinctrl_uart0: uart0grp {
		fsl,pins = <
		VF610_PAD_PTB10__UART0_TX 0x21a2
		VF610_PAD_PTB11__UART0_RX 0x21a1
		>;
		};

		pinctrl_uart1: uart1grp {
		fsl,pins = <
		VF610_PAD_PTB23__UART1_TX 0x21a2
		VF610_PAD_PTB24__UART1_RX 0x21a1
		>;
		};

		pinctrl_uart2: uart2grp {
		fsl,pins = <
		VF610_PAD_PTD0__UART2_TX 0x21a2
		VF610_PAD_PTD1__UART2_RX 0x21a1
		>;
		};

		pinctrl_usb_vbus: pinctrl-usb-vbus {
		fsl,pins = <
		VF610_PAD_PTA16__GPIO_6 0x31c2
		>;
		};

		pinctrl_usb0_host: usb0-host-grp {
		fsl,pins = <
		VF610_PAD_PTD6__GPIO_85 0x0062
		>;
		};
		};

arch/arm/boot/dts/vf610-zii-dev-rev-c.dts

0 → 100644

+414 −0

Original line number	Diff line number	Diff line
		/*
		* Copyright (C) 2015, 2016 Zodiac Inflight Innovations
		*
		* Based on an original 'vf610-twr.dts' which is Copyright 2015,
		* Freescale Semiconductor, Inc.
		*
		* This file is dual-licensed: you can use it either under the terms
		* of the GPL or the X11 license, at your option. Note that this dual
		* licensing only applies to this file, and not this project as a
		* whole.
		*
		* a) This file is free software; you can redistribute it and/or
		* modify it under the terms of the GNU General Public License
		* version 2 as published by the Free Software Foundation.
		*
		* This file is distributed in the hope that it will be useful,
		* but WITHOUT ANY WARRANTY; without even the implied warranty of
		* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
		* GNU General Public License for more details.
		*
		* Or, alternatively,
		*
		* b) Permission is hereby granted, free of charge, to any person
		* obtaining a copy of this software and associated documentation
		* files (the "Software"), to deal in the Software without
		* restriction, including without limitation the rights to use,
		* copy, modify, merge, publish, distribute, sublicense, and/or
		* sell copies of the Software, and to permit persons to whom the
		* Software is furnished to do so, subject to the following
		* conditions:
		*
		* The above copyright notice and this permission notice shall be
		* included in all copies or substantial portions of the Software.
		*
		* THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND,
		* EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
		* OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
		* NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
		* HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
		* WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
		* FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
		* OTHER DEALINGS IN THE SOFTWARE.
		*/

		/dts-v1/;
		#include "vf610-zii-dev.dtsi"

		/ {
		model = "ZII VF610 Development Board, Rev C";
		compatible = "zii,vf610dev-c", "zii,vf610dev", "fsl,vf610";

		mdio-mux {
		compatible = "mdio-mux-gpio";
		pinctrl-0 = <&pinctrl_mdio_mux>;
		pinctrl-names = "default";
		gpios = <&gpio0 8 GPIO_ACTIVE_HIGH
		&gpio0 9 GPIO_ACTIVE_HIGH
		&gpio0 25 GPIO_ACTIVE_HIGH>;
		mdio-parent-bus = <&mdio1>;
		#address-cells = <1>;
		#size-cells = <0>;

		mdio_mux_1: mdio@1 {
		reg = <1>;
		#address-cells = <1>;
		#size-cells = <0>;

		switch0: switch@0 {
		compatible = "marvell,mv88e6190";
		#address-cells = <1>;
		#size-cells = <0>;
		reg = <0>;
		dsa,member = <0 0>;

		ports {
		#address-cells = <1>;
		#size-cells = <0>;

		port@0 {
		reg = <0>;
		label = "cpu";
		ethernet = <&fec1>;

		fixed-link {
		speed = <100>;
		full-duplex;
		};
		};

		port@1 {
		reg = <1>;
		label = "lan1";
		};

		port@2 {
		reg = <2>;
		label = "lan2";
		};

		port@3 {
		reg = <3>;
		label = "lan3";
		};

		port@4 {
		reg = <4>;
		label = "lan4";
		};

		switch0port10: port@10 {
		reg = <10>;
		label = "dsa";
		phy-mode = "xgmii";
		link = <&switch1port10>;
		};
		};
		};
		};

		mdio_mux_2: mdio@2 {
		reg = <2>;
		#address-cells = <1>;
		#size-cells = <0>;

		switch1: switch@0 {
		compatible = "marvell,mv88e6190";
		#address-cells = <1>;
		#size-cells = <0>;
		reg = <0>;
		dsa,member = <0 1>;

		ports {
		#address-cells = <1>;
		#size-cells = <0>;

		port@1 {
		reg = <1>;
		label = "lan5";
		};

		port@2 {
		reg = <2>;
		label = "lan6";
		};

		port@3 {
		reg = <3>;
		label = "lan7";
		};

		port@4 {
		reg = <4>;
		label = "lan8";
		};


		switch1port10: port@10 {
		reg = <10>;
		label = "dsa";
		phy-mode = "xgmii";
		link = <&switch0port10>;
		};
		};
		};
		};

		mdio_mux_4: mdio@4 {
		reg = <4>;
		#address-cells = <1>;
		#size-cells = <0>;
		};
		};
		};

		&dspi0 {
		bus-num = <0>;
		pinctrl-names = "default";
		pinctrl-0 = <&pinctrl_dspi0>;
		status = "okay";
		spi-num-chipselects = <2>;

		m25p128@0 {
		compatible = "m25p128", "jedec,spi-nor";
		#address-cells = <1>;
		#size-cells = <1>;
		reg = <0>;
		spi-max-frequency = <1000000>;
		};

		atzb-rf-233@1 {
		compatible = "atmel,at86rf233";

		pinctrl-names = "default";
		pinctrl-0 = <&pinctr_atzb_rf_233>;

		spi-max-frequency = <7500000>;
		reg = <1>;
		interrupts = <4 IRQ_TYPE_LEVEL_HIGH>;
		interrupt-parent = <&gpio3>;
		xtal-trim = /bits/ 8 <0x06>;

		sleep-gpio = <&gpio0 24 GPIO_ACTIVE_HIGH>;
		reset-gpio = <&gpio6 10 GPIO_ACTIVE_HIGH>;

		fsl,spi-cs-sck-delay = <180>;
		fsl,spi-sck-cs-delay = <250>;
		};
		};

		&i2c0 {
		/*
		* U712
		*
		* Exposed signals:
		* P1 - WE2_CMD
		* P2 - WE2_CLK
		*/
		gpio5: pca9557@18 {
		compatible = "nxp,pca9557";
		reg = <0x18>;
		gpio-controller;
		#gpio-cells = <2>;
		};

		/*
		* U121
		*
		* Exposed signals:
		* I/O0 - ENET_SWR_EN
		* I/O1 - ESW1_RESETn
		* I/O2 - ARINC_RESET
		* I/O3 - DD1_IO_RESET
		* I/O4 - ESW2_RESETn
		* I/O5 - ESW3_RESETn
		* I/O6 - ESW4_RESETn
		* I/O8 - TP909
		* I/O9 - FEM_SEL
		* I/O10 - WIFI_RESETn
		* I/O11 - PHY_RSTn
		* I/O12 - OPT1_SD
		* I/O13 - OPT2_SD
		* I/O14 - OPT1_TX_DIS
		* I/O15 - OPT2_TX_DIS
		*/
		gpio6: sx1503@20 {
		compatible = "semtech,sx1503q";

		pinctrl-names = "default";
		pinctrl-0 = <&pinctrl_sx1503_20>;
		#gpio-cells = <2>;
		#interrupt-cells = <2>;
		reg = <0x20>;
		interrupt-parent = <&gpio0>;
		interrupts = <23 IRQ_TYPE_EDGE_FALLING>;
		gpio-controller;
		interrupt-controller;

		enet_swr_en {
		gpio-hog;
		gpios = <0 GPIO_ACTIVE_HIGH>;
		output-high;
		line-name = "enet-swr-en";
		};
		};

		/*
		* U715
		*
		* Exposed signals:
		* IO0 - WE1_CLK
		* IO1 - WE1_CMD
		*/
		gpio7: pca9554@22 {
		compatible = "nxp,pca9554";
		reg = <0x22>;
		gpio-controller;
		#gpio-cells = <2>;

		};
		};

		&i2c1 {
		at24mac602@00 {
		compatible = "atmel,24c02";
		reg = <0x50>;
		read-only;
		};
		};

		&i2c2 {
		tca9548@70 {
		compatible = "nxp,pca9548";
		pinctrl-0 = <&pinctrl_i2c_mux_reset>;
		pinctrl-names = "default";
		#address-cells = <1>;
		#size-cells = <0>;
		reg = <0x70>;
		reset-gpios = <&gpio3 23 GPIO_ACTIVE_LOW>;

		i2c@0 {
		#address-cells = <1>;
		#size-cells = <0>;
		reg = <0>;
		};

		i2c@1 {
		#address-cells = <1>;
		#size-cells = <0>;
		reg = <1>;

		sfp2: at24c04@50 {
		compatible = "atmel,24c02";
		reg = <0x50>;
		};
		};

		i2c@2 {
		#address-cells = <1>;
		#size-cells = <0>;
		reg = <2>;

		sfp3: at24c04@50 {
		compatible = "atmel,24c02";
		reg = <0x50>;
		};
		};

		i2c@3 {
		#address-cells = <1>;
		#size-cells = <0>;
		reg = <3>;
		};
		};
		};

		&uart3 {
		pinctrl-names = "default";
		pinctrl-0 = <&pinctrl_uart3>;
		status = "okay";
		};

		&gpio0 {
		eth0_intrp {
		gpio-hog;
		gpios = <23 GPIO_ACTIVE_HIGH>;
		input;
		line-name = "sx1503-irq";
		};
		};

		&gpio3 {
		eth0_intrp {
		gpio-hog;
		gpios = <2 GPIO_ACTIVE_HIGH>;
		input;
		line-name = "eth0-intrp";
		};
		};

		&fec0 {
		mdio {
		#address-cells = <1>;
		#size-cells = <0>;
		status = "okay";

		ethernet-phy@0 {
		compatible = "ethernet-phy-ieee802.3-c22";

		pinctrl-names = "default";
		pinctrl-0 = <&pinctrl_fec0_phy_int>;

		interrupt-parent = <&gpio3>;
		interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
		reg = <0>;
		};
		};
		};

		&iomuxc {
		pinctr_atzb_rf_233: pinctrl-atzb-rf-233 {
		fsl,pins = <
		VF610_PAD_PTB2__GPIO_24 0x31c2
		VF610_PAD_PTE27__GPIO_132 0x33e2
		>;
		};


		pinctrl_sx1503_20: pinctrl-sx1503-20 {
		fsl,pins = <
		VF610_PAD_PTB1__GPIO_23 0x219d
		>;
		};

		pinctrl_uart3: uart3grp {
		fsl,pins = <
		VF610_PAD_PTA20__UART3_TX 0x21a2
		VF610_PAD_PTA21__UART3_RX 0x21a1
		>;
		};

		pinctrl_mdio_mux: pinctrl-mdio-mux {
		fsl,pins = <
		VF610_PAD_PTA18__GPIO_8 0x31c2
		VF610_PAD_PTA19__GPIO_9 0x31c2
		VF610_PAD_PTB3__GPIO_25 0x31c2
		>;
		};

		pinctrl_fec0_phy_int: pinctrl-fec0-phy-int {
		fsl,pins = <
		VF610_PAD_PTB28__GPIO_98 0x219d
		>;
		};
		};

arch/arm/boot/dts/vf610-zii-dev.dtsi

0 → 100644

+383 −0

File added.

Preview size limit exceeded, changes collapsed.