Merge branch 'pm-cpufreq'

Intel P-state driver

Intel P-State driver

--------------------

--------------------

This driver provides an interface to control the P state selection for

This driver provides an interface to control the P-State selection for the

SandyBridge+ Intel processors.  The driver can operate two different

SandyBridge+ Intel processors.

modes based on the processor model, legacy mode and Hardware P state (HWP)

mode.

The following document explains P-States:

http://events.linuxfoundation.org/sites/events/files/slides/LinuxConEurope_2015.pdf

In legacy mode, the Intel P-state implements two internal governors,

As stated in the document, P-State doesn’t exactly mean a frequency. However, for

performance and powersave, that differ from the general cpufreq governors of

the sake of the relationship with cpufreq, P-State and frequency are used

the same name (the general cpufreq governors implement target(), whereas the

interchangeably.

internal Intel P-state governors implement setpolicy()).  The internal

performance governor sets the max_perf_pct and min_perf_pct to 100; that is,

Understanding the cpufreq core governors and policies are important before

the governor selects the highest available P state to maximize the performance

discussing more details about the Intel P-State driver. Based on what callbacks

of the core.  The internal powersave governor selects the appropriate P state

a cpufreq driver provides to the cpufreq core, it can support two types of

based on the current load on the CPU.

drivers:

- with target_index() callback: In this mode, the drivers using cpufreq core

In HWP mode P state selection is implemented in the processor

simply provide the minimum and maximum frequency limits and an additional

itself. The driver provides the interfaces between the cpufreq core and

interface target_index() to set the current frequency. The cpufreq subsystem

the processor to control P state selection based on user preferences

has a number of scaling governors ("performance", "powersave", "ondemand",

and reporting frequency to the cpufreq core.  In this mode the

etc.). Depending on which governor is in use, cpufreq core will call for

internal Intel P-state governor code is disabled.

transitions to a specific frequency using target_index() callback.

- setpolicy() callback: In this mode, drivers do not provide target_index()

In addition to the interfaces provided by the cpufreq core for

callback, so cpufreq core can't request a transition to a specific frequency.

controlling frequency the driver provides sysfs files for

The driver provides minimum and maximum frequency limits and callbacks to set a

controlling P state selection. These files have been added to

policy. The policy in cpufreq sysfs is referred to as the "scaling governor".

/sys/devices/system/cpu/intel_pstate/

The cpufreq core can request the driver to operate in any of the two policies:

"performance: and "powersave". The driver decides which frequency to use based

      max_perf_pct: limits the maximum P state that will be requested by

on the above policy selection considering minimum and maximum frequency limits.

      the driver stated as a percentage of the available performance. The

      available (P states) performance may be reduced by the no_turbo

The Intel P-State driver falls under the latter category, which implements the

setpolicy() callback. This driver decides what P-State to use based on the

requested policy from the cpufreq core. If the processor is capable of

selecting its next P-State internally, then the driver will offload this

responsibility to the processor (aka HWP: Hardware P-States). If not, the

driver implements algorithms to select the next P-State.

Since these policies are implemented in the driver, they are not same as the

cpufreq scaling governors implementation, even if they have the same name in

the cpufreq sysfs (scaling_governors). For example the "performance" policy is

similar to cpufreq’s "performance" governor, but "powersave" is completely

different than the cpufreq "powersave" governor. The strategy here is similar

to cpufreq "ondemand", where the requested P-State is related to the system load.

Sysfs Interface

In addition to the frequency-controlling interfaces provided by the cpufreq

core, the driver provides its own sysfs files to control the P-State selection.

These files have been added to /sys/devices/system/cpu/intel_pstate/.

Any changes made to these files are applicable to all CPUs (even in a

multi-package system).

      max_perf_pct: Limits the maximum P-State that will be requested by

      the driver. It states it as a percentage of the available performance. The

      available (P-State) performance may be reduced by the no_turbo

      setting described below.

      setting described below.

      min_perf_pct: limits the minimum P state that will be  requested by

      min_perf_pct: Limits the minimum P-State that will be requested by

      the driver stated as a percentage of the max (non-turbo)

      the driver. It states it as a percentage of the max (non-turbo)

      performance level.

      performance level.

      no_turbo: limits the driver to selecting P states below the turbo

      no_turbo: Limits the driver to selecting P-State below the turbo

      frequency range.

      frequency range.

      turbo_pct: displays the percentage of the total performance that

      turbo_pct: Displays the percentage of the total performance that

      is supported by hardware that is in the turbo range. This number

      is supported by hardware that is in the turbo range. This number

      is independent of whether turbo has been disabled or not.

      is independent of whether turbo has been disabled or not.

      num_pstates: displays the number of pstates that are supported

      num_pstates: Displays the number of P-States that are supported

      by hardware. This number is independent of whether turbo has

      by hardware. This number is independent of whether turbo has

      been disabled or not.

      been disabled or not.

For example, if a system has these parameters:

	Max 1 core turbo ratio: 0x21 (Max 1 core ratio is the maximum P-State)

	Max non turbo ratio: 0x17

	Minimum ratio : 0x08 (Here the ratio is called max efficiency ratio)

Sysfs will show :

	max_perf_pct:100, which corresponds to 1 core ratio

	min_perf_pct:24, max_efficiency_ratio / max 1 Core ratio

	no_turbo:0, turbo is not disabled

	num_pstates:26 = (max 1 Core ratio - Max Efficiency Ratio + 1)

	turbo_pct:39 = (max 1 core ratio - max non turbo ratio) / num_pstates

Refer to "Intel® 64 and IA-32 Architectures Software Developer’s Manual

Volume 3: System Programming Guide" to understand ratios.

cpufreq sysfs for Intel P-State

Since this driver registers with cpufreq, cpufreq sysfs is also presented.

There are some important differences, which need to be considered.

scaling_cur_freq: This displays the real frequency which was used during

the last sample period instead of what is requested. Some other cpufreq driver,

like acpi-cpufreq, displays what is requested (Some changes are on the

way to fix this for acpi-cpufreq driver). The same is true for frequencies

displayed at /proc/cpuinfo.

scaling_governor: This displays current active policy. Since each CPU has a

cpufreq sysfs, it is possible to set a scaling governor to each CPU. But this

is not possible with Intel P-States, as there is one common policy for all

CPUs. Here, the last requested policy will be applicable to all CPUs. It is

suggested that one use the cpupower utility to change policy to all CPUs at the

same time.

scaling_setspeed: This attribute can never be used with Intel P-State.

scaling_max_freq/scaling_min_freq: This interface can be used similarly to

the max_perf_pct/min_perf_pct of Intel P-State sysfs. However since frequencies

are converted to nearest possible P-State, this is prone to rounding errors.

This method is not preferred to limit performance.

affected_cpus: Not used

related_cpus: Not used

For contemporary Intel processors, the frequency is controlled by the

For contemporary Intel processors, the frequency is controlled by the

processor itself and the P-states exposed to software are related to

processor itself and the P-State exposed to software is related to

performance levels.  The idea that frequency can be set to a single

performance levels.  The idea that frequency can be set to a single

frequency is fiction for Intel Core processors. Even if the scaling

frequency is fictional for Intel Core processors. Even if the scaling

driver selects a single P state the actual frequency the processor

driver selects a single P-State, the actual frequency the processor

will run at is selected by the processor itself.

will run at is selected by the processor itself.

For legacy mode debugfs files have also been added to allow tuning of

Tuning Intel P-State driver

the internal governor algorythm. These files are located at

/sys/kernel/debug/pstate_snb/ These files are NOT present in HWP mode.

When HWP mode is not used, debugfs files have also been added to allow the

tuning of the internal governor algorithm. These files are located at

/sys/kernel/debug/pstate_snb/. The algorithm uses a PID (Proportional

Integral Derivative) controller. The PID tunable parameters are:

      deadband

      deadband

      d_gain_pct

      d_gain_pct

      p_gain_pct

      p_gain_pct

      sample_rate_ms

      sample_rate_ms

      setpoint

      setpoint

To adjust these parameters, some understanding of driver implementation is

necessary. There are some tweeks described here, but be very careful. Adjusting

them requires expert level understanding of power and performance relationship.

These limits are only useful when the "powersave" policy is active.

-To make the system more responsive to load changes, sample_rate_ms can

be adjusted  (current default is 10ms).

-To make the system use higher performance, even if the load is lower, setpoint

can be adjusted to a lower number. This will also lead to faster ramp up time

to reach the maximum P-State.

If there are no derivative and integral coefficients, The next P-State will be

equal to:

	current P-State - ((setpoint - current cpu load) * p_gain_pct)

For example, if the current PID parameters are (Which are defaults for the core

processors like SandyBridge):

      deadband = 0

      d_gain_pct = 0

      i_gain_pct = 0

      p_gain_pct = 20

      sample_rate_ms = 10

      setpoint = 97

If the current P-State = 0x08 and current load = 100, this will result in the

next P-State = 0x08 - ((97 - 100) * 0.2) = 8.6 (rounded to 9). Here the P-State

goes up by only 1. If during next sample interval the current load doesn't

change and still 100, then P-State goes up by one again. This process will

continue as long as the load is more than the setpoint until the maximum P-State

is reached.

For the same load at setpoint = 60, this will result in the next P-State

= 0x08 - ((60 - 100) * 0.2) = 16

So by changing the setpoint from 97 to 60, there is an increase of the

next P-State from 9 to 16. So this will make processor execute at higher

P-State for the same CPU load. If the load continues to be more than the

setpoint during next sample intervals, then P-State will go up again till the

maximum P-State is reached. But the ramp up time to reach the maximum P-State

will be much faster when the setpoint is 60 compared to 97.

Debugging Intel P-State driver

Event tracing

To debug P-State transition, the Linux event tracing interface can be used.

There are two specific events, which can be enabled (Provided the kernel

configs related to event tracing are enabled).

# cd /sys/kernel/debug/tracing/

# echo 1 > events/power/pstate_sample/enable

# echo 1 > events/power/cpu_frequency/enable

# cat trace

gnome-terminal--4510  [001] ..s.  1177.680733: pstate_sample: core_busy=107

	scaled=94 from=26 to=26 mperf=1143818 aperf=1230607 tsc=29838618

		freq=2474476

cat-5235  [002] ..s.  1177.681723: cpu_frequency: state=2900000 cpu_id=2

Using ftrace

If function level tracing is required, the Linux ftrace interface can be used.

For example if we want to check how often a function to set a P-State is

called, we can set ftrace filter to intel_pstate_set_pstate.

# cd /sys/kernel/debug/tracing/

# cat available_filter_functions | grep -i pstate

intel_pstate_set_pstate

intel_pstate_cpu_init

...

# echo intel_pstate_set_pstate > set_ftrace_filter

# echo function > current_tracer

# cat trace | head -15

# tracer: function

#

# entries-in-buffer/entries-written: 80/80   #P:4

#

#                              _-----=> irqs-off

#                             / _----=> need-resched

#                            | / _---=> hardirq/softirq

#                            || / _--=> preempt-depth

#                            ||| /     delay

#           TASK-PID   CPU#  ||||    TIMESTAMP  FUNCTION

#              | |       |   ||||       |         |

            Xorg-3129  [000] ..s.  2537.644844: intel_pstate_set_pstate <-intel_pstate_timer_func

 gnome-terminal--4510  [002] ..s.  2537.649844: intel_pstate_set_pstate <-intel_pstate_timer_func

     gnome-shell-3409  [001] ..s.  2537.650850: intel_pstate_set_pstate <-intel_pstate_timer_func

          <idle>-0     [000] ..s.  2537.654843: intel_pstate_set_pstate <-intel_pstate_timer_func

2.2 cpuinfo_transition_latency:

2.2 cpuinfo_transition_latency:

-------------------------------

-------------------------------

The cpuinfo_transition_latency field is 0. The PCC specification does

The cpuinfo_transition_latency field is CPUFREQ_ETERNAL. The PCC specification

not include a field to expose this value currently.

does not include a field to expose this value currently.

2.3 cpuinfo_cur_freq:

2.3 cpuinfo_cur_freq:

---------------------

---------------------

		Definition: Specifies the syscon node controlling the cpu core

		Definition: Specifies the syscon node controlling the cpu core

			    power domains.

			    power domains.

	- dynamic-power-coefficient

		Usage: optional

		Value type: <prop-encoded-array>

		Definition: A u32 value that represents the running time dynamic

			    power coefficient in units of mW/MHz/uVolt^2. The

			    coefficient can either be calculated from power

			    measurements or derived by analysis.

			    The dynamic power consumption of the CPU  is

			    proportional to the square of the Voltage (V) and

			    the clock frequency (f). The coefficient is used to

			    calculate the dynamic power as below -

			    Pdyn = dynamic-power-coefficient * V^2 * f

			    where voltage is in uV, frequency is in MHz.

Example 1 (dual-cluster big.LITTLE system 32-bit):

Example 1 (dual-cluster big.LITTLE system 32-bit):

	cpus {

	cpus {

Binding for ST's CPUFreq driver

===============================

ST's CPUFreq driver attempts to read 'process' and 'version' attributes

from the SoC, then supplies the OPP framework with 'prop' and 'supported

hardware' information respectively.  The framework is then able to read

the DT and operate in the usual way.

For more information about the expected DT format [See: ../opp/opp.txt].

Frequency Scaling only

----------------------

No vendor specific driver required for this.

Located in CPU's node:

- operating-points		: [See: ../power/opp.txt]

Example [safe]

--------------

cpus {

	cpu@0 {

				 /* kHz     uV   */

		operating-points = <1500000 0

				    1200000 0

				    800000  0

				    500000  0>;

	};

};

Dynamic Voltage and Frequency Scaling (DVFS)

--------------------------------------------

This requires the ST CPUFreq driver to supply 'process' and 'version' info.

Located in CPU's node:

- operating-points-v2		: [See ../power/opp.txt]

Example [unsafe]

----------------

cpus {

	cpu@0 {

		operating-points-v2	= <&cpu0_opp_table>;

	};

};

cpu0_opp_table: opp_table {

	compatible = "operating-points-v2";

	/* ############################################################### */

	/* # WARNING: Do not attempt to copy/replicate these nodes,      # */

	/* #          they are only to be supplied by the bootloader !!! # */

	/* ############################################################### */

	opp0 {

		/*			   Major       Minor       Substrate */

		/*			   2           all         all       */

		opp-supported-hw	= <0x00000004  0xffffffff  0xffffffff>;

		opp-hz			= /bits/ 64 <1500000000>;

		clock-latency-ns	= <10000000>;

		opp-microvolt-pcode0	= <1200000>;

		opp-microvolt-pcode1	= <1200000>;

		opp-microvolt-pcode2	= <1200000>;

		opp-microvolt-pcode3	= <1200000>;

		opp-microvolt-pcode4	= <1170000>;

		opp-microvolt-pcode5	= <1140000>;

		opp-microvolt-pcode6	= <1100000>;

		opp-microvolt-pcode7	= <1070000>;

	};

	opp1 {

		/*			   Major       Minor       Substrate */

		/*			   all         all         all       */

		opp-supported-hw	= <0xffffffff  0xffffffff  0xffffffff>;

		opp-hz			= /bits/ 64 <1200000000>;

		clock-latency-ns	= <10000000>;

		opp-microvolt-pcode0	= <1110000>;

		opp-microvolt-pcode1	= <1150000>;

		opp-microvolt-pcode2	= <1100000>;

		opp-microvolt-pcode3	= <1080000>;

		opp-microvolt-pcode4	= <1040000>;

		opp-microvolt-pcode5	= <1020000>;

		opp-microvolt-pcode6	= <980000>;

		opp-microvolt-pcode7	= <930000>;

	};

};

config ARM_BIG_LITTLE_CPUFREQ

config ARM_BIG_LITTLE_CPUFREQ

	tristate "Generic ARM big LITTLE CPUfreq driver"

	tristate "Generic ARM big LITTLE CPUfreq driver"

	depends on (ARM_CPU_TOPOLOGY || ARM64) && HAVE_CLK

	depends on (ARM_CPU_TOPOLOGY || ARM64) && HAVE_CLK

	# if CPU_THERMAL is on and THERMAL=m, ARM_BIT_LITTLE_CPUFREQ cannot be =y

	depends on !CPU_THERMAL || THERMAL

	select PM_OPP

	select PM_OPP

	help

	help

	  This enables the Generic CPUfreq driver for ARM big.LITTLE platforms.

	  This enables the Generic CPUfreq driver for ARM big.LITTLE platforms.

	help

	help

	  This adds the CPUFreq driver support for SPEAr SOCs.

	  This adds the CPUFreq driver support for SPEAr SOCs.

config ARM_STI_CPUFREQ

	tristate "STi CPUFreq support"

	depends on SOC_STIH407

	help

	  This driver uses the generic OPP framework to match the running

	  platform with a predefined set of suitable values.  If not provided

	  we will fall-back so safe-values contained in Device Tree.  Enable

	  this config option if you wish to add CPUFreq support for STi based

	  SoCs.

config ARM_TEGRA20_CPUFREQ

config ARM_TEGRA20_CPUFREQ

	bool "Tegra20 CPUFreq support"

	bool "Tegra20 CPUFreq support"

	depends on ARCH_TEGRA

	depends on ARCH_TEGRA