Merge "dt-bindings: qcom: qpnp-fg-gen4: Add snapshot" (90ea20c9) · Commits · e / devices / android_kernel_fairphone_FP4

Documentation/devicetree/bindings/power/supply/qcom/qpnp-fg-gen4.txt

0 → 100644

+469 −0

Original line number	Diff line number	Diff line
		Qualcomm Technologies, Inc. PMIC Fuel Gauge Gen4 Device

		QTI PMIC FG Gen4 device provides interface to the clients to read properties
		related to the battery. Its main function is to retrieve the State of Charge
		(SOC), in percentage scale representing the amount of charge left in the
		battery.

		=======================
		Required Node Structure
		=======================

		FG Gen4 device must be described in two levels of device nodes. The first
		level describes the FG Gen4 device. The second level describes one or more
		peripherals managed by FG Gen4 driver. All the peripheral specific parameters
		such as base address, interrupts etc., should be under second level node.

		====================================
		First Level Node - FG Gen4 device
		====================================

		- compatible
		Usage: required
		Value type: <string>
		Definition: Should be "qcom,fg-gen4".

		- qcom,pmic-revid
		Usage: required
		Value type: <phandle>
		Definition: Should specify the phandle of PMIC revid module. This is
		used to identify the PMIC subtype.

		- qcom,fg-cutoff-voltage
		Usage: optional
		Value type: <u32>
		Definition: The voltage (in mV) where the fuel gauge will steer the SOC
		to be zero. For example, if the cutoff voltage is set to
		3400mv, the fuel gauge will try to count SoC so that the
		battery SOC will be 0 when it is 3400 mV. If this property
		is not specified, then the default value used will be
		3000 mV.

		- qcom,fg-empty-voltage
		Usage: optional
		Value type: <u32>
		Definition: The voltage threshold (in mV) based on which the empty soc
		interrupt will be triggered. When the empty soc interrupt
		fires, battery soc will be set to 0 and the userspace will
		be notified via the power supply framework. The userspace
		will read 0% soc and immediately shutdown. If this property
		is not specified, then the default value used will be
		2812 mV.

		- qcom,fg-sys-term-current
		Usage: optional
		Value type: <u32>
		Definition: Battery current (in mA) at which the fuel gauge will try to
		scale towards 100%. When the charge current goes above this
		the SOC should be at 100%. If this property is not
		specified, then the default value used will be -125 mA.
		This value has to be specified in negative values for
		the charging current.

		- qcom,fg-cutoff-current
		Usage: optional
		Value type: <u32>
		Definition: Minimum Battery current (in mA) used for cutoff SOC
		estimate. If this property is not specified, then a default
		value of 200 mA will be applied.

		- qcom,fg-delta-soc-thr
		Usage: optional
		Value type: <u32>
		Definition: Percentage of SOC increase upon which the delta monotonic &
		battery SOC interrupts will be triggered. If this property
		is not specified, then the default value will be 1.
		Possible values are in the range of 0 to 12.

		- qcom,fg-esr-timer-chg-fast
		Usage: optional
		Value type: <prop-encoded-array>
		Definition: Number of cycles between ESR pulses while the battery is
		charging for fast calibration. Array of 2 elements if
		specified.
		Element 0 - Retry value for timer
		Element 1 - Maximum value for timer

		- qcom,fg-esr-timer-dischg-fast
		Usage: optional
		Value type: <prop-encoded-array>
		Definition: Number of cycles between ESR pulses while the battery is
		discharging for fast calibration. Array of 2 elements if
		specified.
		Element 0 - Retry value for timer
		Element 1 - Maximum value for timer

		- qcom,fg-esr-timer-chg-slow
		Usage: optional
		Value type: <prop-encoded-array>
		Definition: Number of cycles between ESR pulses while the battery is
		charging for default calibration. Array of 2 elements if
		specified.
		Element 0 - Retry value for timer
		Element 1 - Maximum value for timer

		- qcom,fg-esr-timer-dischg-slow
		Usage: optional
		Value type: <prop-encoded-array>
		Definition: Number of cycles between ESR pulses while the battery is
		discharging for default calibration. Array of 2 elements if
		specified.
		Element 0 - Retry value for timer
		Element 1 - Maximum value for timer

		- qcom,fg-esr-cal-soc-thresh
		Usage: optional
		Value type: <prop-encoded-array>
		Definition: SOC thresholds applied when ESR fast calibration is done.
		Array of 2 elements if specified. This should be specified
		if ESR fast calibration algorithm is needed.
		Element 0 - Minimum SOC threshold in percentage
		Element 1 - Maximum SOC threshold in percentage

		- qcom,fg-esr-cal-temp-thresh
		Usage: optional
		Value type: <prop-encoded-array>
		Definition: Battery temperature thresholds applied when ESR fast
		calibration is done. Array of 2 elements if specified.
		This should be specified if ESR fast calibration algorithm
		is needed.
		Element 0 - Minimum temperature threshold in Celsius
		Element 1 - Maximum temperature threshold in Celsius

		- qcom,fg-delta-esr-disable-count
		Usage: optional
		Value type: <u32>
		Definition: Value after which delta ESR interrupt will be disabled.
		This is applicable only when ESR fast calibration is
		enabled. Default value is 10.

		- qcom,fg-delta-esr-thr
		Usage: optional
		Value type: <u32>
		Definition: Threshold for delta ESR interrupt in uOhms. Default value
		is 1832. If ESR fast calibration algorithm is enabled, this
		will be overridden with a maximum value.

		- qcom,fg-esr-filter-factor
		Usage: optional
		Value type: <u32>
		Definition: ESR filter factor used in ESR fast calibration algorithm.
		This factor will be used when ESR correction delta is
		applied after the calculation. Default value is 2.

		- qcom,fg-esr-pulse-thresh-ma
		Usage: optional
		Value type: <u32>
		Definition: ESR pulse qualification threshold in mA. If this is not
		specified, a default value of 110 mA will be configured.
		Allowed values are from 1 to 1000.

		- qcom,fg-esr-meas-curr-ma
		Usage: optional
		Value type: <u32>
		Definition: ESR measurement current in mA. If this is not specified,
		a default value of 120 mA will be configured. Allowed
		values are 60, 120, 180 and 240.

		- qcom,fg-batt-temp-delta
		Usage: optional
		Value type: <u32>
		Definition: Battery temperature delta interrupt threshold. Possible
		values are: 0, 1, 2 and 3. Unit is in Kelvin or Celsius.

		- qcom,fg-batt-temp-cold-thresh
		Usage: optional
		Value type: <u32>
		Definition: Battery temperature cold interrupt threshold. Allowed
		values are from -128 to 127. Unit is in Kelvin or Celsius.

		- qcom,fg-batt-temp-hot-thresh
		Usage: optional
		Value type: <u32>
		Definition: Battery temperature hot interrupt threshold. Allowed
		values are from -128 to 127. Unit is in Kelvin or Celsius.

		- qcom,fg-batt-temp-hyst
		Usage: optional
		Value type: <u32>
		Definition: Battery temperature hysteresis threshold. This will be
		applicable only if the cold and hot thresholds are
		specified. Possible values are: 0, 1, 2 and 3. Unit is in
		Kelvin or Celsius.

		- qcom,fg-force-load-profile
		Usage: optional
		Value type: <empty>
		Definition: If set, battery profile will be force loaded if the profile
		loaded earlier by bootloader doesn't match with the profile
		available in the device tree.

		- qcom,cl-start-capacity
		Usage: optional
		Value type: <u32>
		Definition: Battery SOC threshold to start the capacity learning.
		If this is not specified, then the default value used
		will be 15. Unit is in percentage.

		- qcom,cl-min-temp
		Usage: optional
		Value type: <u32>
		Definition: Lower limit of battery temperature to start the capacity
		learning. If this is not specified, then the default value
		used will be 150 (15 C). Unit is in decidegC.

		- qcom,cl-max-temp
		Usage: optional
		Value type: <u32>
		Definition: Upper limit of battery temperature to start the capacity
		learning. If this is not specified, then the default value
		used will be 500 (50 C). Unit is in decidegC.

		- qcom,cl-max-increment
		Usage: optional
		Value type: <u32>
		Definition: Maximum capacity increment allowed per capacity learning
		cycle. If this is not specified, then the default value
		used will be 5 (0.5%). Unit is in decipercentage.

		- qcom,cl-max-decrement
		Usage: optional
		Value type: <u32>
		Definition: Maximum capacity decrement allowed per capacity learning
		cycle. If this is not specified, then the default value
		used will be 100 (10%). Unit is in decipercentage.

		- qcom,cl-min-limit
		Usage: optional
		Value type: <u32>
		Definition: Minimum limit that the capacity cannot go below in a
		capacity learning cycle. If this is not specified, then
		the default value is 0. Unit is in decipercentage.

		- qcom,cl-max-limit
		Usage: optional
		Value type: <u32>
		Definition: Maximum limit that the capacity cannot go above in a
		capacity learning cycle. If this is not specified, then
		the default value is 0. Unit is in decipercentage.

		- qcom,hold-soc-while-full
		Usage: optional
		Value type: <empty>
		Definition: A boolean property that when defined holds SOC at 100% when
		the battery is full.

		- qcom,linearize-soc
		Usage: optional
		Value type: <empty>
		Definition: A boolean property that when defined linearizes SOC when
		the SOC drops after charge termination monotonically to
		improve the user experience. This is applicable only if
		"qcom,hold-soc-while-full" is specified.

		- qcom,ki-coeff-soc-dischg
		Usage: optional
		Value type: <prop-encoded-array>
		Definition: Array of monotonic SOC threshold values to change the ki
		coefficient for medium discharge current during discharge.
		This should be defined in the ascending order and in the
		range of 0-100. Array limit is set to 3.

		- qcom,ki-coeff-low-dischg
		Usage: optional
		Value type: <prop-encoded-array>
		Definition: Array of ki coefficient values for low discharge current
		during discharge. These values will be applied when the
		monotonic SOC goes below the SOC threshold specified under
		qcom,ki-coeff-soc-dischg. Array limit is set to 3. This
		property should be specified if qcom,ki-coeff-soc-dischg
		is specified to make it fully functional. Value has no
		unit. Allowed range is 62 to 15564 in micro units.

		- qcom,ki-coeff-med-dischg
		Usage: optional
		Value type: <prop-encoded-array>
		Definition: Array of ki coefficient values for medium discharge current
		during discharge. These values will be applied when the
		monotonic SOC goes below the SOC threshold specified under
		qcom,ki-coeff-soc-dischg. Array limit is set to 3. This
		property should be specified if qcom,ki-coeff-soc-dischg
		is specified to make it fully functional. Value has no
		unit. Allowed range is 62 to 15564 in micro units.

		- qcom,ki-coeff-hi-dischg
		Usage: optional
		Value type: <prop-encoded-array>
		Definition: Array of ki coefficient values for high discharge current
		during discharge. These values will be applied when the
		monotonic SOC goes below the SOC threshold specified under
		qcom,ki-coeff-soc-dischg. Array limit is set to 3. This
		property should be specified if qcom,ki-coeff-soc-dischg
		is specified to make it fully functional. Value has no
		unit. Allowed range is 62 to 15564 in micro units.

		- qcom,ki-coeff-low-chg
		Usage: optional
		Value type: <u32>
		Definition: ki coefficient value for low charge current during
		charging. Value has no unit. Allowed range is 62 to 15564
		in micro units.

		- qcom,ki-coeff-med-chg
		Usage: optional
		Value type: <u32>
		Definition: ki coefficient value for medium charge current during
		charging. Value has no unit. Allowed range is 62 to 15564
		in micro units.

		- qcom,ki-coeff-hi-chg
		Usage: optional
		Value type: <u32>
		Definition: ki coefficient value for high charge current during
		charging. Value has no unit. Allowed range is 62 to 15564
		in micro units.

		- qcom,ki-coeff-full-dischg
		Usage: optional
		Value type: <prop-encoded-array>
		Definition: Array of Ki coefficient full SOC values that needs to be
		applied during discharging. If not specified, a value of
		0 will be set.
		Allowed range is from 62 to 15564.
		Element 0 - Ki coefficient for full SOC in room temperature
		Element 1 - Ki coefficient for full SOC in low temperature

		- qcom,fg-rconn-uohms
		Usage: optional
		Value type: <u32>
		Definition: Battery connector resistance (Rconn) in microohms. If it's
		already configured in bootloader, then it will not be
		configured again by GEN4 FG driver.

		- qcom,slope-limit-temp-threshold
		Usage: optional
		Value type: <u32>
		Definition: Battery temperature threshold to decide when slope limit
		coefficients should be applied along with charging status.
		Unit is in decidegC.

		- qcom,slope-limit-coeffs
		Usage: optional
		Value type: <prop-encoded-array>
		Definition: A list of integers which holds the slope limit coefficients
		in the following order. Allowed size is 4. Possible values
		are from 123 to 31128. Unit is in micro-percentage.
		Element 0 - Low temperature discharging
		Element 1 - Low temperature charging
		Element 2 - High temperature discharging
		Element 3 - High temperature charging
		These coefficients have to be specified along with the
		property "qcom,slope-limit-temp-threshold" to make dynamic
		slope limit adjustment functional.

		- qcom,rapid-soc-dec-en
		Usage: optional
		Value type: <empty>
		Definition: A boolean property that when defined enables rapid SOC
		decrease when the battery SOC is low but not converging to
		zero with battery voltage dropping rapidly below Vcutoff.

		- qcom,five-pin-battery
		Usage: optional
		Value type: <empty>
		Definition: A boolean property that when specified indicates that a
		five pin battery is used. Based on this, time to full
		calculations would use the Rbatt calculated properly.

		==========================================================
		Second Level Nodes - Peripherals managed by FG Gen4 driver
		==========================================================
		- reg
		Usage: required
		Value type: <prop-encoded-array>
		Definition: Addresses and sizes for the specified peripheral

		- interrupts
		Usage: optional
		Value type: <prop-encoded-array>
		Definition: Interrupt mapping as per the interrupt encoding

		- interrupt-names
		Usage: optional
		Value type: <stringlist>
		Definition: Interrupt names. This list must match up 1-to-1 with the
		interrupts specified in the 'interrupts' property.

		========
		Example
		========

		pm8150b_fg: qpnp,fg {
		compatible = "qcom,fg-gen4";
		#address-cells = <1>;
		#size-cells = <1>;
		qcom,pmic-revid = <&pm8150b_revid>;
		status = "okay";

		qcom,fg-batt-soc@4000 {
		status = "okay";
		reg = <0x4000 0x100>;
		interrupts = <0x2 0x40 0x0 IRQ_TYPE_EDGE_BOTH>,
		<0x2 0x40 0x1 IRQ_TYPE_EDGE_BOTH>,
		<0x2 0x40 0x2 IRQ_TYPE_EDGE_RISING>,
		<0x2 0x40 0x3 IRQ_TYPE_EDGE_RISING>,
		<0x2 0x40 0x4 IRQ_TYPE_EDGE_BOTH>,
		<0x2 0x40 0x5 IRQ_TYPE_EDGE_RISING>,
		<0x2 0x40 0x6 IRQ_TYPE_EDGE_BOTH>,
		<0x2 0x40 0x7 IRQ_TYPE_EDGE_BOTH>;
		interrupt-names = "soc-update",
		"soc-ready",
		"bsoc-delta",
		"msoc-delta",
		"msoc-low",
		"msoc-empty",
		"msoc-high",
		"msoc-full";

		};

		qcom,fg-batt-info@4100 {
		status = "okay";
		reg = <0x4100 0x100>;
		interrupts = <0x2 0x41 0x0 IRQ_TYPE_EDGE_BOTH>,
		<0x2 0x41 0x1 IRQ_TYPE_EDGE_BOTH>,
		<0x2 0x41 0x3 IRQ_TYPE_EDGE_BOTH>;
		interrupt-names = "vbatt-low",
		"vbatt-pred-delta",
		"esr-delta";
		};

		qcom,adc-rr@4200 {
		status = "okay";
		reg = <0x4200 0x100>;
		interrupts = <0x2 0x42 0x0 IRQ_TYPE_EDGE_BOTH>,
		<0x2 0x42 0x1 IRQ_TYPE_EDGE_BOTH>,
		<0x2 0x42 0x2 IRQ_TYPE_EDGE_BOTH>,
		<0x2 0x42 0x3 IRQ_TYPE_EDGE_BOTH>,
		<0x2 0x42 0x4 IRQ_TYPE_EDGE_BOTH>;
		interrupt-names = "batt-missing",
		"batt-id",
		"batt-temp-delta",
		"batt-temp-hot",
		"batt-temp-cold";
		};

		qcom,fg-memif@4300 {
		status = "okay";
		reg = <0x4300 0x100>;
		interrupts = <0x2 0x43 0x0 IRQ_TYPE_EDGE_BOTH>,
		<0x2 0x43 0x1 IRQ_TYPE_EDGE_BOTH>,
		<0x2 0x43 0x2 IRQ_TYPE_EDGE_BOTH>,
		<0x2 0x43 0x3 IRQ_TYPE_EDGE_BOTH>,
		interrupt-names = "ima-rdy",
		"ima-xcp",
		"dma-xcp",
		"dma-grant",
		};

		};

Documentation/devicetree/bindings/power/supply/qcom/qpnp-qnovo5.txt

0 → 100644

+40 −0

Original line number	Diff line number	Diff line
		QPNP Qnovo5 pulse engine

		QPNP Qnovo5 is a PBS based pulse charging engine which works in tandem with the
		QPNP SMB5 Charger device. It configures the QPNP SMB5 charger to
		charge/discharge as per pulse characteristics.

		The QPNP Qnovo5 pulse engine has a single peripheral assigned to it.

		Properties:
		- compatible:
		Usage: required
		Value type: <string>
		Definition: It must be "qcom,qpnp-qnovo5".

		- reg:
		Usage: required
		Value type: <u32>
		Definition: Specifies the base address of the module. Qnovo5 is using a
		SDAM peripheral so this is the address of the SDAM module
		being used.

		- interrupts:
		Usage: required
		Value type: <prop-encoded-array>
		Definition: Specifies the interrupt associated with Qnovo5.

		- interrupt-names:
		Usage: required
		Value type: <string>
		Definition: Specifies the interrupt name for Qnovo5. There is only one
		interrupt named as "ptrain-done".

		Example:

		qcom,qpnp-qnovo@b000 {
		compatible = "qcom,qpnp-qnovo5";
		reg = <0xb000 0x100>;
		interrupts = <0x2 0xb0 0x1 IRQ_TYPE_NONE>;
		interrupt-names = "ptrain-done";
		};

drivers/power/supply/qcom/Kconfig

+19 −0

Original line number	Diff line number	Diff line
		@@ -27,4 +27,23 @@ config SMB1390_CHARGE_PUMP_PSY
		Technologies, Inc.’s family of standalone chargers to enable a high
		current, low profile Li+ battery charging system.

		config SMB1355_SLAVE_CHARGER
		tristate "SMB1355 Slave Battery Charger"
		depends on MFD_I2C_PMIC
		help
		Say Y to include support for SMB1355 Battery Charger.
		SMB1355 is a single phase 5A battery charger.
		The driver supports charger enable/disable.
		The driver reports the charger status via the power supply framework.
		A charger status change triggers an IRQ via the device STAT pin.

		config QPNP_QNOVO5
		bool "QPNP QNOVO5 driver"
		depends on MFD_SPMI_PMIC
		help
		Say Y here to enable the Qnovo5 PBS-based pulse charging engine.
		Qnovo5 driver accepts pulse parameters via sysfs entries and programs
		the hardware module. It also allows userspace code to read diagnostics
		of voltage and current measured during certain phases of the pulses.

		endmenu

drivers/power/supply/qcom/Makefile

+2 −0

Original line number	Diff line number	Diff line
		@@ -2,3 +2,5 @@

		obj-$(CONFIG_QPNP_SMB5) += step-chg-jeita.o battery.o qpnp-smb5.o smb5-lib.o pmic-voter.o storm-watch.o schgm-flash.o
		obj-$(CONFIG_SMB1390_CHARGE_PUMP_PSY) += smb1390-charger-psy.o pmic-voter.o
		obj-$(CONFIG_SMB1355_SLAVE_CHARGER) += smb1355-charger.o pmic-voter.o
		obj-$(CONFIG_QPNP_QNOVO5) += qpnp-qnovo5.o battery.o pmic-voter.o

drivers/power/supply/qcom/qpnp-qnovo5.c

0 → 100644

+1393 −0

File added.

Preview size limit exceeded, changes collapsed.