Merge "ARM: dts: qcom: Support TOF camera for lito qrd platform" (6d44259e) · Commits · e / devices / android_kernel_fairphone_FP4

qcom/lito-camera-sensor-qrd.dtsi

+48 −0

Original line number	Diff line number	Diff line
		@@ -46,6 +46,16 @@
		switch-source = <&pm8150l_switch2>;
		};

		vreg_tof: regulator-dbb1 {
		compatible = "regulator-fixed";
		regulator-name = "vdd_tof";
		regulator-min-microvolt = <3600000>;
		regulator-max-microvolt = <3600000>;
		gpio = <&pm8150l_gpios 2 GPIO_ACTIVE_HIGH>;
		startup-delay-us = <1000>;
		enable-active-high;
		};

		qcom,cam-res-mgr {
		compatible = "qcom,cam-res-mgr";
		status = "ok";
		@@ -621,4 +631,42 @@
		clock-cntl-level = "turbo";
		clock-rates = <24000000>;
		};

		qcom,cam-sensor@3 {
		cell-index = <3>;
		compatible = "qcom,cam-sensor";
		csiphy-sd-index = <3>;
		sensor-position-roll = <270>;
		sensor-position-pitch = <0>;
		sensor-position-yaw = <0>;
		cam_vio-supply = <&L7P>;
		cam_vdig-supply = <&vreg_tof>;
		cam_clk-supply = <&titan_top_gdsc>;
		regulator-names = "cam_vio", "cam_vdig",
		"cam_clk";
		rgltr-cntrl-support;
		rgltr-min-voltage = <1800000 3600000 0>;
		rgltr-max-voltage = <1800000 3600000 0>;
		rgltr-load-current = <0 120000 0>;
		gpio-no-mux = <0>;
		pinctrl-names = "cam_default", "cam_suspend";
		pinctrl-0 = <&cam_sensor_mclk3_active
		&cam_sensor_active_3>;
		pinctrl-1 = <&cam_sensor_mclk3_suspend
		&cam_sensor_suspend_3>;
		gpios = <&tlmm 16 0>,
		<&tlmm 23 0>;
		gpio-reset = <1>;
		gpio-req-tbl-num = <0 1>;
		gpio-req-tbl-flags = <1 0>;
		gpio-req-tbl-label = "CAMIF_MCLK3",
		"CAM_RESET3";
		sensor-mode = <0>;
		cci-master = <0>;
		status = "ok";
		clocks = <&camcc CAM_CC_MCLK3_CLK>;
		clock-names = "cam_clk";
		clock-cntl-level = "turbo";
		clock-rates = <24000000>;
		};
		};

+29 −0

Original line number	Diff line number	Diff line
		@@ -789,6 +789,35 @@
		};
		};

		cam_sensor_active_3: cam_sensor_active_3 {
		/* RESET TOF */
		mux {
		pins = "gpio23";
		function = "gpio";
		};

		config {
		pins = "gpio23";
		bias-disable; /* No PULL */
		drive-strength = <2>; /* 2 MA */
		};
		};

		cam_sensor_suspend_3: cam_sensor_suspend_3 {
		/* RESET TOF */
		mux {
		pins = "gpio23";
		function = "gpio";
		};

		config {
		pins = "gpio23";
		bias-pull-down; /* PULL DOWN */
		drive-strength = <2>; /* 2 MA */
		output-low;
		};
		};

		cam_sensor_active_front: cam_sensor_active_front {
		/* RESET FRONT */
		mux {