Revert existing FBE changes for ICE FBE

Introduction:

=============

Storage encryption has been one of the most required feature from security

point of view. QTI based storage encryption solution uses general purpose

crypto engine. While this kind of solution provide a decent amount of

performance, it falls short as storage speed is improving significantly

continuously. To overcome performance degradation, newer chips are going to

have Inline Crypto Engine (ICE) embedded into storage device. ICE is supposed

to meet the line speed of storage devices.

Hardware Description

====================

ICE is a HW block that is embedded into storage device such as UFS/eMMC. By

default, ICE works in bypass mode i.e. ICE HW does not perform any crypto

operation on data to be processed by storage device. If required, ICE can be

configured to perform crypto operation in one direction (i.e. either encryption

or decryption) or in both direction(both encryption & decryption).

When a switch between the operation modes(plain to crypto or crypto to plain)

is desired for a particular partition, SW must complete all transactions for

that particular partition before switching the crypto mode i.e. no crypto, one

direction crypto or both direction crypto operation. Requests for other

partitions are not impacted due to crypto mode switch.

ICE HW currently supports AES128/256 bit ECB & XTS mode encryption algorithms.

Keys for crypto operations are loaded from SW. Keys are stored in a lookup

table(LUT) located inside ICE HW. Maximum of 32 keys can be loaded in ICE key

LUT. A Key inside the LUT can be referred using a key index.

SW Description

==============

ICE HW has catagorized ICE registers in 2 groups: those which can be accessed by

only secure side i.e. TZ and those which can be accessed by non-secure side such

as HLOS as well. This requires that ICE driver to be split in two pieces: one

running from TZ space and another from HLOS space.

ICE driver from TZ would configure keys as requested by HLOS side.

ICE driver on HLOS side is responsible for initialization of ICE HW.

SW Architecture Diagram

=======================

Following are all the components involved in the ICE driver for control path:

+++++++++++++++++++++++++++++++++++++++++

+               App layer               +

+++++++++++++++++++++++++++++++++++++++++

+             System layer              +

+   ++++++++         +++++++            +

+   + VOLD +         + PFM +            +

+   ++++++++         +++++++            +

+         ||         ||                 +

+         ||         ||                 +

+         \/         \/                 +

+        ++++++++++++++                 +

+        + LibQSEECom +                 +

+        ++++++++++++++                 +

+++++++++++++++++++++++++++++++++++++++++

+             Kernel                    +       +++++++++++++++++

+                                       +       +     KMS       +

+  +++++++  +++++++++++  +++++++++++    +       +++++++++++++++++

+  + ICE +  + Storage +  + QSEECom +    +       +   ICE Driver  +

+++++++++++++++++++++++++++++++++++++++++ <===> +++++++++++++++++

               ||                                    ||

               ||                                    ||

               \/                                    \/

+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++

+                      Storage Device                           +

+                      ++++++++++++++                           +

+                      +   ICE HW   +                           +

+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++

Use Cases:

----------

a) Device bootup

ICE HW is detected during bootup time and corresponding probe function is

called. ICE driver parses its data from device tree node. ICE HW and storage

HW are tightly coupled. Storage device probing is dependent upon ICE device

probing. ICE driver configures all the required registers to put the ICE HW

in bypass mode.

b) Configuring keys

Currently, there are couple of use cases to configure the keys.

1) Full Disk Encryption(FDE)

System layer(VOLD) at invocation of apps layer would call libqseecom to create

the encryption key. Libqseecom calls qseecom driver to communicate with KMS

module on the secure side i.e. TZ. KMS would call ICE driver on the TZ side to

create and set the keys in ICE HW. At the end of transaction, VOLD would have

key index of key LUT where encryption key is present.

2) Per File Encryption (PFE)

Per File Manager(PFM) calls QSEECom api to create the key. PFM has a peer comp-

onent(PFT) at kernel layer which gets the corresponding key index from PFM.

Following are all the components involved in the ICE driver for data path:

+++++++++++++++++++++++++++++++++++++++++

+               App layer               +

+++++++++++++++++++++++++++++++++++++++++

+              VFS                      +

+---------------------------------------+

+         File System (EXT4)            +

+---------------------------------------+

+             Block Layer               +

+ --------------------------------------+

+                              +++++++  +

+              dm-req-crypt => + PFT +  +

+                              +++++++  +

+                                       +

+---------------------------------------+

+    +++++++++++           +++++++      +

+    + Storage +           + ICE +      +

+++++++++++++++++++++++++++++++++++++++++

+                  ||                   +

+                  || (Storage Req with +

+                  \/  ICE parameters ) +

+++++++++++++++++++++++++++++++++++++++++

+          Storage Device               +

+          ++++++++++++++               +

+          +   ICE HW   +               +

+++++++++++++++++++++++++++++++++++++++++

c) Data transaction

Once the crypto key has been configured, VOLD/PFM creates device mapping for

data partition. As part of device mapping VOLD passes key index, crypto

algorithm, mode and key length to dm layer. In case of PFE, keys are provided

by PFT as and when request is processed by dm-req-crypt. When any application

needs to read/write data, it would go through DM layer which would add crypto

information, provided by VOLD/PFT, to Request. For each Request, Storage driver

would ask ICE driver to configure crypto part of request. ICE driver extracts

crypto data from Request structure and provide it to storage driver which would

finally dispatch request to storage device.

d) Error Handling

Due to issue # 1 mentioned in "Known Issues", ICE driver does not register for

any interrupt. However, it enables sources of interrupt for ICE HW. After each

data transaction, Storage driver receives transaction completion event. As part

of event handling, storage driver calls  ICE driver to check if any of ICE

interrupt status is set. If yes, storage driver returns error to upper layer.

Error handling would be changed in future chips.

Interfaces

==========

ICE driver exposes interfaces for storage driver to :

1. Get the global instance of ICE driver

2. Get the implemented interfaces of the particular ice instance

3. Initialize the ICE HW

4. Reset the ICE HW

5. Resume/Suspend the ICE HW

6. Get the Crypto configuration for the data request for storage

7. Check if current data transaction has generated any interrupt

Driver Parameters

=================

This driver is built and statically linked into the kernel; therefore,

there are no module parameters supported by this driver.

There are no kernel command line parameters supported by this driver.

Power Management

================

ICE driver does not do power management on its own as it is part of storage

hardware. Whenever storage driver receives request for power collapse/suspend

resume, it would call ICE driver which exposes APIs for Storage HW. ICE HW

during power collapse or reset, wipes crypto configuration data. When ICE

driver receives request to resume, it would ask ICE driver on TZ side to

restore the configuration. ICE driver does not do anything as part of power

collapse or suspend event.

Interface:

==========

ICE driver exposes following APIs for storage driver to use:

int (*init)(struct platform_device *, void *, ice_success_cb, ice_error_cb);

	-- This function is invoked by storage controller during initialization of

	storage controller. Storage controller would provide success and error call

	backs which would be invoked asynchronously once ICE HW init is done.

int (*reset)(struct platform_device *);

	-- ICE HW reset as part of storage controller reset. When storage controller

	received reset command, it would call reset on ICE HW. As of now, ICE HW

	does not need to do anything as part of reset.

int (*resume)(struct platform_device *);

	-- ICE HW while going to reset, wipes all crypto keys and other data from ICE

	HW. ICE driver would reconfigure those data as part of resume operation.

int (*suspend)(struct platform_device *);

	-- This API would be called by storage driver when storage device is going to

	suspend mode. As of today, ICE driver does not do anything to handle suspend.

int (*config)(struct platform_device *, struct request* , struct ice_data_setting*);

	-- Storage driver would call this interface to get all crypto data required to

	perform crypto operation.

int (*status)(struct platform_device *);

	-- Storage driver would call this interface to check if previous data transfer

	generated any error.

Config options

==============

This driver is enabled by the kernel config option CONFIG_CRYPTO_DEV_MSM_ICE.

Dependencies

============

ICE driver depends upon corresponding ICE driver on TZ side to function

appropriately.

Known Issues

============

1. ICE HW emits 0s even if it has generated an interrupt

This issue has significant impact on how ICE interrupts are handled. Currently,

ICE driver does not register for any of the ICE interrupts but enables the

sources of interrupt. Once storage driver asks to check the status of interrupt,

it reads and clears the clear status and provide read status to storage driver.

This mechanism though not optimal but prevents filesystem curruption.

This issue has been fixed in newer chips.

2. ICE HW wipes all crypto data during power collapse

This issue necessiate that ICE driver on TZ side store the crypto material

which is not required in the case of general purpose crypto engine.

This issue has been fixed in newer chips.

Further Improvements

====================

Currently, Due to PFE use case, ICE driver is dependent upon dm-req-crypt to

provide the keys as part of request structure. This couples ICE driver with

dm-req-crypt based solution. It is under discussion to expose an IOCTL based

and registration based interface APIs from ICE driver. ICE driver would use

these two interfaces to find out if any key exists for current request. If

yes, choose the right key index received from IOCTL or registration based

APIs. If not, dont set any crypto parameter in the request.

CONFIG_SCSI_UFSHCD=y

CONFIG_SCSI_UFSHCD_PLATFORM=y

CONFIG_SCSI_UFS_QCOM=y

CONFIG_SCSI_UFS_QCOM_ICE=y

CONFIG_MD=y

CONFIG_BLK_DEV_DM=y

CONFIG_DM_CRYPT=y

CONFIG_DM_DEFAULT_KEY=y

CONFIG_DM_UEVENT=y

CONFIG_DM_VERITY=y

CONFIG_DM_VERITY_FEC=y

CONFIG_MMC_BLOCK_DEFERRED_RESUME=y

CONFIG_MMC_SDHCI=y

CONFIG_MMC_SDHCI_PLTFM=y

CONFIG_MMC_SDHCI_MSM_ICE=y

CONFIG_MMC_SDHCI_MSM=y

CONFIG_NEW_LEDS=y

CONFIG_LEDS_CLASS=y

# CONFIG_NETWORK_FILESYSTEMS is not set

CONFIG_NLS_CODEPAGE_437=y

CONFIG_NLS_ISO8859_1=y

CONFIG_PFK=y

CONFIG_SECURITY_PERF_EVENTS_RESTRICT=y

CONFIG_SECURITY=y

CONFIG_LSM_MMAP_MIN_ADDR=4096

CONFIG_CRYPTO_DEV_QCOM_MSM_QCE=y

CONFIG_CRYPTO_DEV_QCRYPTO=y

CONFIG_CRYPTO_DEV_QCEDEV=y

CONFIG_CRYPTO_DEV_QCOM_ICE=y

CONFIG_PRINTK_TIME=y

CONFIG_DEBUG_INFO=y

CONFIG_FRAME_WARN=2048

CONFIG_SCSI_UFSHCD=y

CONFIG_SCSI_UFSHCD_PLATFORM=y

CONFIG_SCSI_UFS_QCOM=y

CONFIG_SCSI_UFS_QCOM_ICE=y

CONFIG_MD=y

CONFIG_BLK_DEV_DM=y

CONFIG_DM_CRYPT=y

CONFIG_DM_DEFAULT_KEY=y

CONFIG_DM_UEVENT=y

CONFIG_DM_VERITY=y

CONFIG_DM_VERITY_FEC=y

CONFIG_MMC_IPC_LOGGING=y

CONFIG_MMC_SDHCI=y

CONFIG_MMC_SDHCI_PLTFM=y

CONFIG_MMC_SDHCI_MSM_ICE=y

CONFIG_MMC_SDHCI_MSM=y

CONFIG_NEW_LEDS=y

CONFIG_LEDS_CLASS=y

CONFIG_NLS_CODEPAGE_437=y

CONFIG_NLS_ASCII=y

CONFIG_NLS_ISO8859_1=y

CONFIG_PFK=y

CONFIG_SECURITY_PERF_EVENTS_RESTRICT=y

CONFIG_SECURITY=y

CONFIG_LSM_MMAP_MIN_ADDR=4096

CONFIG_CRYPTO_DEV_QCOM_MSM_QCE=y

CONFIG_CRYPTO_DEV_QCRYPTO=y

CONFIG_CRYPTO_DEV_QCEDEV=y

CONFIG_CRYPTO_DEV_QCOM_ICE=y

CONFIG_XZ_DEC=y

CONFIG_PRINTK_TIME=y

CONFIG_DYNAMIC_DEBUG=y

CONFIG_SCSI_UFSHCD=y

CONFIG_SCSI_UFSHCD_PLATFORM=y

CONFIG_SCSI_UFS_QCOM=y

CONFIG_SCSI_UFS_QCOM_ICE=y

CONFIG_MD=y

CONFIG_BLK_DEV_DM=y

CONFIG_DM_CRYPT=y

CONFIG_DM_DEFAULT_KEY=y

CONFIG_DM_UEVENT=y

CONFIG_DM_VERITY=y

CONFIG_DM_VERITY_FEC=y

CONFIG_MMC_BLOCK_DEFERRED_RESUME=y

CONFIG_MMC_SDHCI=y

CONFIG_MMC_SDHCI_PLTFM=y

CONFIG_MMC_SDHCI_MSM_ICE=y

CONFIG_MMC_SDHCI_MSM=y

CONFIG_NEW_LEDS=y

CONFIG_LEDS_CLASS=y

# CONFIG_NETWORK_FILESYSTEMS is not set

CONFIG_NLS_CODEPAGE_437=y

CONFIG_NLS_ISO8859_1=y

CONFIG_PFK=y

CONFIG_SECURITY_PERF_EVENTS_RESTRICT=y

CONFIG_SECURITY=y

CONFIG_HARDENED_USERCOPY=y

CONFIG_CRYPTO_DEV_QCOM_MSM_QCE=y

CONFIG_CRYPTO_DEV_QCRYPTO=y

CONFIG_CRYPTO_DEV_QCEDEV=y

CONFIG_CRYPTO_DEV_QCOM_ICE=y

CONFIG_STACK_HASH_ORDER_SHIFT=12

CONFIG_PRINTK_TIME=y

CONFIG_DEBUG_INFO=y

CONFIG_SCSI_UFSHCD=y

CONFIG_SCSI_UFSHCD_PLATFORM=y

CONFIG_SCSI_UFS_QCOM=y

CONFIG_SCSI_UFS_QCOM_ICE=y

CONFIG_SCSI_UFSHCD_CMD_LOGGING=y

CONFIG_MD=y

CONFIG_BLK_DEV_DM=y

CONFIG_DM_CRYPT=y

CONFIG_DM_DEFAULT_KEY=y

CONFIG_DM_UEVENT=y

CONFIG_DM_VERITY=y

CONFIG_DM_VERITY_FEC=y

CONFIG_MMC_IPC_LOGGING=y

CONFIG_MMC_SDHCI=y

CONFIG_MMC_SDHCI_PLTFM=y

CONFIG_MMC_SDHCI_MSM_ICE=y

CONFIG_MMC_SDHCI_MSM=y

CONFIG_NEW_LEDS=y

CONFIG_LEDS_CLASS=y

# CONFIG_NETWORK_FILESYSTEMS is not set

CONFIG_NLS_CODEPAGE_437=y

CONFIG_NLS_ISO8859_1=y

CONFIG_PFK=y

CONFIG_SECURITY_PERF_EVENTS_RESTRICT=y

CONFIG_SECURITY=y

CONFIG_HARDENED_USERCOPY=y

CONFIG_CRYPTO_DEV_QCOM_MSM_QCE=y

CONFIG_CRYPTO_DEV_QCRYPTO=y

CONFIG_CRYPTO_DEV_QCEDEV=y

CONFIG_CRYPTO_DEV_QCOM_ICE=y

CONFIG_PRINTK_TIME=y

CONFIG_DYNAMIC_DEBUG=y

CONFIG_DEBUG_CONSOLE_UNHASHED_POINTERS=y