hwmon: add support for Sensirion SHTC1 sensor (1a539d37) · Commits · e / devices / android_kernel_fairphone_FP4

Documentation/hwmon/shtc1

0 → 100644

+43 −0

Original line number	Diff line number	Diff line
		Kernel driver shtc1
		===================

		Supported chips:
		* Sensirion SHTC1
		Prefix: 'shtc1'
		Addresses scanned: none
		Datasheet: http://www.sensirion.com/file/datasheet_shtc1

		* Sensirion SHTW1
		Prefix: 'shtw1'
		Addresses scanned: none
		Datasheet: Not publicly available

		Author:
		Johannes Winkelmann <johannes.winkelmann@sensirion.com>

		Description
		-----------

		This driver implements support for the Sensirion SHTC1 chip, a humidity and
		temperature sensor. Temperature is measured in degrees celsius, relative
		humidity is expressed as a percentage. Driver can be used as well for SHTW1
		chip, which has the same electrical interface.

		The device communicates with the I2C protocol. All sensors are set to I2C
		address 0x70. See Documentation/i2c/instantiating-devices for methods to
		instantiate the device.

		There are two options configurable by means of shtc1_platform_data:
		1. blocking (pull the I2C clock line down while performing the measurement) or
		non-blocking mode. Blocking mode will guarantee the fastest result but
		the I2C bus will be busy during that time. By default, non-blocking mode
		is used. Make sure clock-stretching works properly on your device if you
		want to use blocking mode.
		2. high or low accuracy. High accuracy is used by default and using it is
		strongly recommended.

		sysfs-Interface
		---------------

		temp1_input - temperature input
		humidity1_input - humidity input

drivers/hwmon/Kconfig

+10 −0

Original line number	Diff line number	Diff line
		@@ -1124,6 +1124,16 @@ config SENSORS_SHT21
		This driver can also be built as a module. If so, the module
		will be called sht21.

		config SENSORS_SHTC1
		tristate "Sensiron humidity and temperature sensors. SHTC1 and compat."
		depends on I2C
		help
		If you say yes here you get support for the Sensiron SHTC1 and SHTW1
		humidity and temperature sensors.

		This driver can also be built as a module. If so, the module
		will be called shtc1.

		config SENSORS_S3C
		tristate "Samsung built-in ADC"
		depends on S3C_ADC

drivers/hwmon/Makefile

+1 −0

Original line number	Diff line number	Diff line
		@@ -126,6 +126,7 @@ obj-$(CONFIG_SENSORS_SCH5627) += sch5627.o
		obj-$(CONFIG_SENSORS_SCH5636) += sch5636.o
		obj-$(CONFIG_SENSORS_SHT15) += sht15.o
		obj-$(CONFIG_SENSORS_SHT21) += sht21.o
		obj-$(CONFIG_SENSORS_SHTC1) += shtc1.o
		obj-$(CONFIG_SENSORS_SIS5595) += sis5595.o
		obj-$(CONFIG_SENSORS_SMM665) += smm665.o
		obj-$(CONFIG_SENSORS_SMSC47B397)+= smsc47b397.o

drivers/hwmon/shtc1.c

0 → 100644

+251 −0

Original line number	Diff line number	Diff line
		/* Sensirion SHTC1 humidity and temperature sensor driver
		*
		* Copyright (C) 2014 Sensirion AG, Switzerland
		* Author: Johannes Winkelmann <johannes.winkelmann@sensirion.com>
		*
		* This program is free software; you can redistribute it and/or modify
		* it under the terms of the GNU General Public License as published by
		* the Free Software Foundation; either version 2 of the License, or
		* (at your option) any later version.
		*
		* This program is distributed in the hope that it will be useful,
		* but WITHOUT ANY WARRANTY; without even the implied warranty of
		* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
		* GNU General Public License for more details.
		*
		*/

		#include <linux/module.h>
		#include <linux/init.h>
		#include <linux/slab.h>
		#include <linux/i2c.h>
		#include <linux/hwmon.h>
		#include <linux/hwmon-sysfs.h>
		#include <linux/err.h>
		#include <linux/delay.h>
		#include <linux/platform_data/shtc1.h>

		/* commands (high precision mode) */
		static const unsigned char shtc1_cmd_measure_blocking_hpm[] = { 0x7C, 0xA2 };
		static const unsigned char shtc1_cmd_measure_nonblocking_hpm[] = { 0x78, 0x66 };

		/* commands (low precision mode) */
		static const unsigned char shtc1_cmd_measure_blocking_lpm[] = { 0x64, 0x58 };
		static const unsigned char shtc1_cmd_measure_nonblocking_lpm[] = { 0x60, 0x9c };

		/* command for reading the ID register */
		static const unsigned char shtc1_cmd_read_id_reg[] = { 0xef, 0xc8 };

		/* constants for reading the ID register */
		#define SHTC1_ID 0x07
		#define SHTC1_ID_REG_MASK 0x1f

		/* delays for non-blocking i2c commands, both in us */
		#define SHTC1_NONBLOCKING_WAIT_TIME_HPM 14400
		#define SHTC1_NONBLOCKING_WAIT_TIME_LPM 1000

		#define SHTC1_CMD_LENGTH 2
		#define SHTC1_RESPONSE_LENGTH 6

		struct shtc1_data {
		struct i2c_client *client;
		struct mutex update_lock;
		bool valid;
		unsigned long last_updated; /* in jiffies */

		const unsigned char *command;
		unsigned int nonblocking_wait_time; /* in us */

		struct shtc1_platform_data setup;

		int temperature; /* 1000 * temperature in dgr C */
		int humidity; /* 1000 * relative humidity in %RH */
		};

		static int shtc1_update_values(struct i2c_client *client,
		struct shtc1_data *data,
		char *buf, int bufsize)
		{
		int ret = i2c_master_send(client, data->command, SHTC1_CMD_LENGTH);
		if (ret != SHTC1_CMD_LENGTH) {
		dev_err(&client->dev, "failed to send command: %d\n", ret);
		return ret < 0 ? ret : -EIO;
		}

		/*
		* In blocking mode (clock stretching mode) the I2C bus
		* is blocked for other traffic, thus the call to i2c_master_recv()
		* will wait until the data is ready. For non blocking mode, we
		* have to wait ourselves.
		*/
		if (!data->setup.blocking_io)
		usleep_range(data->nonblocking_wait_time,
		data->nonblocking_wait_time + 1000);

		ret = i2c_master_recv(client, buf, bufsize);
		if (ret != bufsize) {
		dev_err(&client->dev, "failed to read values: %d\n", ret);
		return ret < 0 ? ret : -EIO;
		}

		return 0;
		}

		/* sysfs attributes */
		static struct shtc1_data shtc1_update_client(struct device dev)
		{
		struct shtc1_data *data = dev_get_drvdata(dev);
		struct i2c_client *client = data->client;
		unsigned char buf[SHTC1_RESPONSE_LENGTH];
		int val;
		int ret = 0;

		mutex_lock(&data->update_lock);

		if (time_after(jiffies, data->last_updated + HZ / 10) \|\| !data->valid) {
		ret = shtc1_update_values(client, data, buf, sizeof(buf));
		if (ret)
		goto out;

		/*
		* From datasheet:
		* T = -45 + 175 * ST / 2^16
		* RH = 100 * SRH / 2^16
		*
		* Adapted for integer fixed point (3 digit) arithmetic.
		*/
		val = be16_to_cpup((__be16 *)buf);
		data->temperature = ((21875 * val) >> 13) - 45000;
		val = be16_to_cpup((__be16 *)(buf + 3));
		data->humidity = ((12500 * val) >> 13);

		data->last_updated = jiffies;
		data->valid = true;
		}

		out:
		mutex_unlock(&data->update_lock);

		return ret == 0 ? data : ERR_PTR(ret);
		}

		static ssize_t temp1_input_show(struct device *dev,
		struct device_attribute *attr,
		char *buf)
		{
		struct shtc1_data *data = shtc1_update_client(dev);
		if (IS_ERR(data))
		return PTR_ERR(data);

		return sprintf(buf, "%d\n", data->temperature);
		}

		static ssize_t humidity1_input_show(struct device *dev,
		struct device_attribute attr, char buf)
		{
		struct shtc1_data *data = shtc1_update_client(dev);
		if (IS_ERR(data))
		return PTR_ERR(data);

		return sprintf(buf, "%d\n", data->humidity);
		}

		static DEVICE_ATTR_RO(temp1_input);
		static DEVICE_ATTR_RO(humidity1_input);

		static struct attribute *shtc1_attrs[] = {
		&dev_attr_temp1_input.attr,
		&dev_attr_humidity1_input.attr,
		NULL
		};

		ATTRIBUTE_GROUPS(shtc1);

		static void shtc1_select_command(struct shtc1_data *data)
		{
		if (data->setup.high_precision) {
		data->command = data->setup.blocking_io ?
		shtc1_cmd_measure_blocking_hpm :
		shtc1_cmd_measure_nonblocking_hpm;
		data->nonblocking_wait_time = SHTC1_NONBLOCKING_WAIT_TIME_HPM;

		} else {
		data->command = data->setup.blocking_io ?
		shtc1_cmd_measure_blocking_lpm :
		shtc1_cmd_measure_nonblocking_lpm;
		data->nonblocking_wait_time = SHTC1_NONBLOCKING_WAIT_TIME_LPM;
		}
		}

		static int shtc1_probe(struct i2c_client *client,
		const struct i2c_device_id *id)
		{
		int ret;
		char id_reg[2];
		struct shtc1_data *data;
		struct device *hwmon_dev;
		struct i2c_adapter *adap = client->adapter;
		struct device *dev = &client->dev;

		if (!i2c_check_functionality(adap, I2C_FUNC_I2C)) {
		dev_err(dev, "plain i2c transactions not supported\n");
		return -ENODEV;
		}

		ret = i2c_master_send(client, shtc1_cmd_read_id_reg, SHTC1_CMD_LENGTH);
		if (ret != SHTC1_CMD_LENGTH) {
		dev_err(dev, "could not send read_id_reg command: %d\n", ret);
		return ret < 0 ? ret : -ENODEV;
		}
		ret = i2c_master_recv(client, id_reg, sizeof(id_reg));
		if (ret != sizeof(id_reg)) {
		dev_err(dev, "could not read ID register: %d\n", ret);
		return -ENODEV;
		}
		if ((id_reg[1] & SHTC1_ID_REG_MASK) != SHTC1_ID) {
		dev_err(dev, "ID register doesn't match\n");
		return -ENODEV;
		}

		data = devm_kzalloc(dev, sizeof(*data), GFP_KERNEL);
		if (!data)
		return -ENOMEM;

		data->setup.blocking_io = false;
		data->setup.high_precision = true;
		data->client = client;

		if (client->dev.platform_data)
		data->setup = (struct shtc1_platform_data )dev->platform_data;
		shtc1_select_command(data);
		mutex_init(&data->update_lock);

		hwmon_dev = devm_hwmon_device_register_with_groups(dev,
		client->name,
		data,
		shtc1_groups);
		if (IS_ERR(hwmon_dev))
		dev_dbg(dev, "unable to register hwmon device\n");

		return PTR_ERR_OR_ZERO(hwmon_dev);
		}

		/* device ID table */
		static const struct i2c_device_id shtc1_id[] = {
		{ "shtc1", 0 },
		{ "shtw1", 0 },
		{ }
		};
		MODULE_DEVICE_TABLE(i2c, shtc1_id);

		static struct i2c_driver shtc1_i2c_driver = {
		.driver.name = "shtc1",
		.probe = shtc1_probe,
		.id_table = shtc1_id,
		};

		module_i2c_driver(shtc1_i2c_driver);

		MODULE_AUTHOR("Johannes Winkelmann <johannes.winkelmann@sensirion.com>");
		MODULE_DESCRIPTION("Sensirion SHTC1 humidity and temperature sensor driver");
		MODULE_LICENSE("GPL");

include/linux/platform_data/shtc1.h

0 → 100644

+23 −0

Original line number	Diff line number	Diff line
		/*
		* Copyright (C) 2014 Sensirion AG, Switzerland
		* Author: Johannes Winkelmann <johannes.winkelmann@sensirion.com>
		*
		* This software is licensed under the terms of the GNU General Public
		* License version 2, as published by the Free Software Foundation, and
		* may be copied, distributed, and modified under those terms.
		*
		* This program is distributed in the hope that it will be useful,
		* but WITHOUT ANY WARRANTY; without even the implied warranty of
		* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
		* GNU General Public License for more details.
		*
		*/

		#ifndef __SHTC1_H_
		#define __SHTC1_H_

		struct shtc1_platform_data {
		bool blocking_io;
		bool high_precision;
		};
		#endif /* __SHTC1_H_ */