power: qpnp-fg: Add snapshot of the FG driver

					this. If this property is not specified,

					low battery voltage threshold will be

					configured to 4200 mV.

- qcom,fg-rconn-mohm:			Battery connector resistance (Rconn) in

					milliohms. If Rconn is specified, then

					Rslow values will be updated to account

					it for an accurate ESR.

- qcom,cycle-counter-en:		Boolean property which enables the cycle

					counter feature. If this property is

					present, then the following properties

					battery voltage shadow and the current

					predicted voltage in uV to initiate

					capacity learning.

- qcom,cl-max-limit-deciperc:		The maximum percent that the capacity

					cannot go above during any capacity

					learning cycle. This property is in the

					unit of .1% increments.

- qcom,cl-min-limit-deciperc:		The minimum percent that the capacity

					cannot go below during any capacity

					learning cycle. This property is in the

					unit of .1% increments.

- qcom,capacity-estimation-on:		A boolean property to have the fuel

					gauge driver attempt to estimate the

					battery capacity using battery

					settings will be different from default.

					Once SOC crosses 5%, ESR pulse timings

					will be restored back to default.

- qcom,fg-control-slope-limiter:	A boolean property to specify if SOC

					slope limiter coefficients needs to

					be modified based on charging status

					and battery temperature threshold.

- qcom,fg-slope-limit-temp-threshold:	Temperature threshold in decidegC used

					for applying the slope coefficient based

					on charging status and battery

					temperature. If this property is not

					specified, a default value of 100 (10C)

					will be applied by default.

- qcom,fg-slope-limit-low-temp-chg:	When the temperature goes below the

					specified temperature threshold and

					battery is charging, slope coefficient

					specified with this property will be

					applied. If this property is not

					specified, a default value of 45 will be

					applied.

- qcom,fg-slope-limit-low-temp-dischg:	Same as "qcom,fg-slope-limit-low-temp-chg"

					except this is when the battery is

					discharging.

- qcom,fg-slope-limit-high-temp-chg:	When the temperature goes above the

					specified temperature threshold and

					battery is charging, slope coefficient

					specified with this property will be

					applied. If this property is not

					specified, a default value of 2 will be

					applied.

- qcom,fg-slope-limit-high-temp-dischg:	Same as "qcom,fg-slope-limit-high-temp-chg"

					except this is when the battery is

					discharging.

- qcom,fg-dischg-voltage-gain-ctrl:	A boolean property to specify if the

					voltage gain needs to be modified

					during discharging based on monotonic

					soc.

- qcom,fg-dischg-voltage-gain-soc:	Array of monotonic SOC threshold values

					to change the voltage gain settings

					during discharge. This should be defined

					in the ascending order and in the range

					of 0-100. Array limit is set to 3.

					If qcom,fg-dischg-voltage-gain-ctrl is

					set, then this property should be

					specified to apply the gain settings.

- qcom,fg-dischg-med-voltage-gain:	Array of voltage gain values that needs

					to be applied to medC voltage gain when

					the monotonic SOC goes below the SOC

					threshold specified under

					qcom,fg-dischg-voltage-gain-soc. Array

					limit is set to 3.

					If qcom,fg-dischg-voltage-gain-ctrl is

					set, then this property should be

					specified to apply the gain setting.

- qcom,fg-dischg-high-voltage-gain:	Array of voltage gain values that needs

					to be applied to highC voltage gain when

					the monotonic SOC goes below the SOC

					threshold specified under

					qcom,fg-dischg-voltage-gain-soc. Array

					limit is set to 3.

					If qcom,fg-dischg-voltage-gain-ctrl is

					set, then this property should be

					specified to apply the gain setting.

- qcom,fg-use-vbat-low-empty-soc:	A boolean property to specify whether

					vbatt-low interrupt is used to handle

					empty battery condition. If this is

					not specified, empty battery condition

					is detected by empty-soc interrupt.

- qcom,fg-batt-temp-low-limit:		Battery temperature (in decidegC) low

					limit  which will be used to validate

					the battery temperature reading from FG.

					If the battery temperature goes below

					this limit, last read good temperature

					will be notified to userspace. If this

					limit is not specified, then the

					default limit would be -60C.

- qcom,fg-batt-temp-high-limit:		Battery temperature (in decidegC) high

					limit  which will be used to validate

					the battery temperature reading from FG.

					If the battery temperature goes above

					this limit, last read good temperature

					will be notified to userspace. If this

					limit is not specified, then the

					default limit would be 150C.

- qcom,fg-cc-soc-limit-pct:		Percentage of CC_SOC before resetting

					FG and restore the full CC_SOC value.

- qcom,fg-restore-batt-info:		A boolean property to specify whether

					battery parameters needs to be

					restored. If this feature is enabled,

					then validating the battery parameters

					by OCV/battery SOC, validation range

					in percentage should be specified via

					appropriate module parameters to make

					it work properly.

qcom,fg-soc node required properties:

- reg : offset and length of the PMIC peripheral register map.