leds: remove unused driver leds-qpnp-flash.c

Qualcomm Technologies PNP Flash LED

QPNP (Qualcomm Technologies Plug N Play) Flash LED (Light

Emitting Diode) driver is used to provide illumination to

camera sensor when background light is dim to capture good

picture. It can also be used for flashlight/torch application.

It is part of PMIC on Qualcomm Technologies reference platforms.

The PMIC is connected to the host processor via SPMI bus.

Required properties:

- compatible		: should be "qcom,qpnp-flash-led"

- reg			: base address and size for flash LED modules

Optional properties:

- qcom,headroom		: headroom to use. Values should be 250, 300,

			  400 and 500 in mV.

- qcom,startup-dly	: delay before flashing after flash executed.

			  Values should 10, 32, 64, and 128 in us.

- qcom,clamp-curr	: current to clamp at when voltage droop happens.

			  Values are in integer from 0 to 1000 inclusive,

			  indicating 0 to 1000 mA.

- qcom,self-check-enabled : boolean type. self fault check enablement

- qcom,thermal-derate-enabled : boolean type. derate enablement when module

				temperature reaches threshold

- qcom,thermal-derate-threshold : thermal threshold for derate. Values

				should be 95, 105, 115, 125 in C.

- qcom,thermal-derate-rate	: derate rate when module temperature

				reaches threshold. Values should be

				"1_PERCENT", "1P25_PERCENT", "2_PERCENT",

				"2P5_PERCENT", "5_PERCENT" in string.

- qcom,current-ramp-enabled	: boolean type. stepped current ramp enablement

- qcom,ramp-up-step		: current ramp up rate. Values should be

				  "0P2US", "0P4US", "0P8US", "1P6US", "3P3US",

				  "6P7US", "13P5US", "27US".

- qcom,ramp-dn-step		: current ramp down rate. Values should be

				  "0P2US", "0P4US", "0P8US", "1P6US", "3P3US",

				  "6P7US", "13P5US", "27US".

- qcom,vph-pwr-droop-enabled	: boolean type. VPH power droop enablement. Enablement

				  allows current clamp when phone power drops below

				  pre-determined threshold

- qcom,vph-pwr-droop-threshold	: VPH power threshold for module to clamp current.

				  Values are 2500 - 3200 in mV with 100 mV steps.

- qcom,vph-pwr-droop-debounce-time : debounce time for module to confirm a voltage

				     droop is happening. Values are 0, 10, 32, 64

				     in us.

- qcom,pmic-charger-support	: Boolean type. This tells if flash utilizes charger boost

				  support

- qcom,headroom-sense-ch0-enabled: Boolean type. This configures headroom sensing enablement

				   for LED channel 0

- qcom,headroom-sense-ch1-enabled: Boolean type. This configures headroom sensing enablement

				   for LED channel 1

- qcom,power-detect-enabled	: Boolean type. This enables driver to get maximum flash LED

				  current at current battery level to avoid intensity clamp

				  when battery voltage is low

- qcom,otst2-moduled-enabled	: Boolean type. This enables driver to enable MASK to support

				OTST2 connection.

- qcom,follow-otst2-rb-disabled	: Boolean type. This allows driver to reset/deset module.

				By default, driver resets module. This entry allows driver to

				bypass reset module sequence.

- qcom,die-current-derate-enabled: Boolean type. This enables driver to get maximum flash LED

                                   current, based on PMIC die temperature threshold to

				   avoid significant current derate from hardware. This property

				   is not needed if PMIC is older than PMI8994v2.0.

- qcom,die-temp-vadc		: VADC channel source for flash LED. This property is not

				  needed if PMIC is older than PMI8994v2.0.

- qcom,die-temp-threshold       : Integer type array for PMIC die temperature threshold.

				  Array should have at least one value. Values should be in

				  celcius. This property is not needed if PMIC is older than

				  PMI8994v2.0.

- qcom,die-temp-derate-current	: Integer type arrray for PMIC die temperature derate

				  current. Array should have at least one value. Values

				  should be in mA. This property is not needed if PMIC is older

				  than PMI8994v2.0.

Required properties inside child node. Chile node contains settings for each individual LED.

Each LED hardware needs a node for itself and a switch node to control brightness.

For the purpose of turning on/off LED and better regulator control, "led:switch" node

is introduced. "led:switch" acquires several existing properties from other nodes for

operational simplification. For backward compatibility purpose, switch node can be optional:

- label			: type of led that will be used, either "flash" or "torch".

- qcom,led-name		: name of the LED. Accepted values are "led:flash_0",

			  "led:flash_1", "led:torch_0", "led:torch_1"

- qcom,default-led-trigger	: trigger for the camera flash and torch. Accepted values are

				"flash0_trigger", "flash1_trigger", "torch0_trigger", torch1_trigger"

- qcom,id		: enumerated ID for each physical LED. Accepted values are "0",

			  "1", etc..

- qcom,max-current	: maximum current allowed on this LED. Valid values should be

			  integer from 0 to 1000 inclusive, indicating 0 to 1000 mA.

- qcom,pmic-revid	: PMIC revision id source. This property is needed for PMI8996

			revision check.

Optional properties inside child node:

- qcom,current		: default current intensity for LED. Accepted values should be

			  integer from 0 t 1000 inclusive, indicating 0 to 1000 mA.

- qcom,duration	: Duration for flash LED. When duration time expires, hardware will turn off

		flash LED. Values should be from 10 ms to 1280 ms with 10 ms incremental

		step. Not applicable to torch. It is required for LED:SWITCH node to handle

		LED used as flash.

- reg<n>	: reg<n> (<n> represents number. eg 0,1,2,..) property is to add support for

		multiple power sources. It includes two properties regulator-name and max-voltage.

		Required property inside regulator node:

		- regulator-name	: This denotes this node is a regulator node and which

					regulator to use.

		Optional property inside regulator node:

		- max-voltage		: This specifies max voltage of regulator. Some switch

					or boost regulator does not need this property.

Example:

	qcom,leds@d300 {

		compatible = "qcom,qpnp-flash-led";

		status = "okay";

		reg = <0xd300 0x100>;

		label = "flash";

		qcom,headroom = <500>;

		qcom,startup-dly = <128>;

		qcom,clamp-curr = <200>;

		qcom,pmic-charger-support;

		qcom,self-check-enabled;

		qcom,thermal-derate-enabled;

		qcom,thermal-derate-threshold = <80>;

		qcom,thermal-derate-rate = "4_PERCENT";

		qcom,current-ramp-enabled;

		qcom,ramp_up_step = "27US";

		qcom,ramp_dn_step = "27US";

		qcom,vph-pwr-droop-enabled;

		qcom,vph-pwr-droop-threshold = <3200>;

		qcom,vph-pwr-droop-debounce-time = <10>;

		qcom,headroom-sense-ch0-enabled;

		qcom,headroom-sense-ch1-enabled;

		qcom,die-current-derate-enabled;

		qcom,die-temp-vadc = <&pmi8994_vadc>;

		qcom,die-temp-threshold = <85 80 75 70 65>;

		qcom,die-temp-derate-current = <400 800 1200 1600 2000>;

		qcom,pmic-revid = <&pmi8994_revid>;

		pm8226_flash0: qcom,flash_0 {

			label = "flash";

			qcom,led-name = "led:flash_0";

			qcom,default-led-trigger =

					"flash0_trigger";

			qcom,max-current = <1000>;

			qcom,id = <0>;

			qcom,duration = <1280>;

			qcom,current = <625>;

		};

		pm8226_torch: qcom,torch_0 {

			label = "torch";

			qcom,led-name = "led:torch_0";

			qcom,default-led-trigger =

					"torch0_trigger";

			boost-supply = <&pm8226_chg_boost>;

			qcom,max-current = <200>;

			qcom,id = <0>;

			qcom,current = <120>;

			qcom,max-current = <200>;

			reg0 {

				regulator-name =

					 "pm8226_chg_boost";

				max-voltage = <3600000>;

			};

		};

		pm8226_switch: qcom,switch {

			lable = "switch";

			qcom,led-name = "led:switch";

			qcom,default-led-trigger =

					"switch_trigger";

			qcom,id = <2>;

			qcom,current = <625>;

			qcom,duration = <1280>;

			qcom,max-current = <1000>;

			reg0 {

				regulator-name =

					"pm8226_chg_boost";

				max-voltage = <3600000>;

			};

		};

	};

	  LEDs in both PWM and light pattern generator (LPG) modes.  For older

	  PMICs, it also supports WLEDs and flash LEDs.

config LEDS_QPNP_FLASH

	tristate "Support for QPNP Flash LEDs"

	depends on LEDS_CLASS && SPMI

	help

	  This driver supports the flash LED functionality of Qualcomm

	  Technologies, Inc. QPNP PMICs.  This driver supports PMICs up through

	  PM8994.  It can configure the flash LED target current for several

	  independent channels.

config LEDS_QPNP_FLASH_V2

	tristate "Support for QPNP V2 Flash LEDs"

	depends on LEDS_CLASS && MFD_SPMI_PMIC && !LEDS_QPNP_FLASH

	depends on LEDS_CLASS && MFD_SPMI_PMIC

	help

	  This driver supports the flash V2 LED functionality of Qualcomm

	  Technologies, Inc. QPNP PMICs.  This driver supports PMICs starting

obj-$(CONFIG_LEDS_PM8058)		+= leds-pm8058.o

obj-$(CONFIG_LEDS_MLXCPLD)		+= leds-mlxcpld.o

obj-$(CONFIG_LEDS_QPNP)			+= leds-qpnp.o

obj-$(CONFIG_LEDS_QPNP_FLASH)		+= leds-qpnp-flash.o

obj-$(CONFIG_LEDS_QPNP_FLASH_V2)	+= leds-qpnp-flash-v2.o

obj-$(CONFIG_LEDS_QPNP_WLED)		+= leds-qpnp-wled.o

obj-$(CONFIG_LEDS_QPNP_HAPTICS)	+= leds-qpnp-haptics.o