esoc: Snapshot esoc drivers

Attached MDM Modem Devices

External modems are devices that are attached to the msm and controlled by gpios.

There is also a data channel between the msm and the external modem that sometimes needs

to be reset.

Required Properties:

- compatible:	The bus devices need to be compatible with

		"qcom,mdm2-modem", "qcom,ext-mdm9x25", "qcom,ext-mdm9x35", "qcom, ext-mdm9x45",

		"qcom,ext-mdm9x55".

Required named gpio properties:

- qcom,mdm2ap-errfatal-gpio: gpio for the external modem to indicate to the apps processor

		of an error fatal condition on the modem.

- qcom,ap2mdm-errfatal-gpio: gpio for the apps processor to indicate to the external modem

		of an error fatal condition on the apps processor.

- qcom,mdm2ap-status-gpio: gpio to indicate to the apps processor when there is a watchdog

		bite on the external modem.

- qcom,ap2mdm-status-gpio: gpio for the apps processor to indicate to the modem that an apps

		processor watchdog bite has occurred.

- qcom,ap2mdm-soft-reset-gpio: gpio for the apps processor to use to soft-reset the external

		modem. If the flags parameter has a value of 0x1 then the gpio is active LOW.

Required Interrupts:

- "err_fatal_irq": Interrupt generated on the apps processor when the error fatal gpio is pulled

		high by the external modem.

- "status_irq": Interrupt generated on the apps processor when the mdm2ap-status gpio falls low

		on the external modem. This usually indicates a watchdog bite on the modem.

- "plbrdy_irq": Interrupt generated on the aps processor when the mdm2ap-pblrdy gpio is pulled

		either high or low by the external modem. This is an indication that the modem

		has rebooted.

- "mdm2ap_vddmin_irq": Interrupt generated on the apps processor when the external modem goes

		into vddmin power state.

Optional named gpio properties:

- qcom,mdm2ap-pblrdy-gpio: gpio used by some external modems to indicate when the modem has

		booted into the PBL bootloader.

- qcom,ap2mdm-wakeup-gpio: gpio used by the apps processor to wake the external modem

		out of a low power state.

- qcom,ap2mdm-chnl-rdy-gpio: gpio used by the apps processor to inform the external modem

		that data link is ready.

- qcom,mdm2ap-wakeup-gpio: gpio from the external modem to the apps processor to wake it

		out of a low power state.

- qcom,ap2mdm-vddmin-gpio: gpio to indicate to the external modem when the apps processor

		is about to enter vddmin power state.

- qcom,mdm2ap-vddmin-gpio: gpio used by the external modem to inform the apps processor

		when it is about to enter vddmin power state.

- qcom,ap2mdm-kpdpwr-gpio: gpio used to simulate a power button press on the external

		modem. Some modems use this as part of their initial power-up sequence.

		If the "flags" parameter has a value of 0x1 then it is active LOW.

- qcom,ap2mdm-pmic-pwr-en-gpio: Some modems need this gpio for the apps processor to enable

		the pmic on the external modem.

- qcom,use-usb-port-gpio: some modems use this gpio to switch a port connection from uart to usb.

		This is used during firmware upgrade of some modems.

- qcom,mdm-link-detect-gpio: some modems may support two interfaces. This gpio

		indicates whether only one or both links can be used.

Optional driver parameters:

- qcom,ramdump-delay-ms: time in milliseconds to wait before starting to collect ramdumps.

		This interval is the time to wait after an error on the external modem is

		signaled to the apps processor before starting to collect ramdumps. Its

		value depends on the type of external modem (e.g. MDM vs QSC), and how

		error fatal handing is done on the modem.

		The default value is 2 seconds (2000 milliseconds) as specified by the

		mdm9x15 software developer. Consultation with the developer of the modem

		software is required to determine this value for that modem.

- qcom,ps-hold-delay-ms: minimum delay in milliseconds between consecutive PS_HOLD toggles.

		SGLTE targets that use a QSC1215 modem require a minimum delay between consecutive

		toggling of the PS_HOLD pmic input. For one target it is 500 milliseconds but it

		may vary depending on the target and how the external modem is connected. The value

		is specified by the hardware designers.

- qcom,early-power-on: boolean flag to indicate if to power on the modem when the device is probed.

- qcom,sfr-query: boolean flag to indicate if to query the modem for a reset reason.

- qcom,no-powerdown-after-ramdumps: boolean flag to indicate if to power down the modem after ramdumps.

- qcom,no-a2m-errfatal-on-ssr: boolean to tell driver not to raise ap2mdm errfatal during SSR.

- qcom,no-reset-on-first-powerup: boolean to tell driver not to reset the modem when first

		powering up the modem.

- qcom,ramdump-timeout-ms: ramdump timeout interval in milliseconds.

		This interval is the time to wait for collection of the external modem's ramdump

		to complete. It's value depends on the speed of the data connection between the

		external modem and the apps processor on the platform. If the connection is a

		UART port then this delay needs to be longer in order to avoid premature timeout

		of the ramdump collection.

		The default value is 2 minutes (120000 milliseconds) which is based on the

		measured time it takes over a UART connection. It is reduced when the data

		connection is an HSIC port. The value is usually tuned empirically for a

		particular target.

- qcom,image-upgrade-supported: boolean flag to indicate if software upgrade is supported.

- qcom,support-shutdown: boolean flag to indicate if graceful shutdown is supported.

- qcom,vddmin-drive-strength: drive strength in milliamps of the ap2mdm-vddmin gpio.

		The ap2mdm_vddmin gpio is controlled by the RPM processor. It is pulled low

		to indicate to the external modem that the apps processor has entered vddmin

		state, and high to indicate the reverse. Its parameters are passed to the RPM

		software from the HLOS because the RPM software has to way of saving this type

		of configuration when an external modem is attached.

		The value of the drive strength is specified by the hardware designers. A value

		of 8 milliamps is typical.

		This property is ignored if the property "qcom,ap2mdm-vddmin-gpio" is

		not set.

- qcom,vddmin-modes: a string indicating the "modes" requested for the ap2mdm-vddmin gpio.

		This value is passed to RPM and is used by the RPM module to determine the

		gpio mux function. The only currently supported modes string is "normal" and

		corresponds to the value 0x03 that is passed to RPM.

- qcom,restart-group: List of subsystems that will need to restart together.

- qcom,mdm-dual-link: Boolean indicates whether both links can used for

		communication.

- qcom,ssctl-instance-id: Instance id used by the subsystem to connect with the SSCTL service.

- qcom,sysmon-id: platform device id that sysmon is probed with for the subsystem.

- qcom,pil-force-shutdown: Boolean. If set, the SSR framework will not trigger graceful shutdown

			   on behalf of the subsystem driver.

Example:

	mdm0: qcom,mdm0 {

                compatible = "qcom,mdm2-modem";

		cell-index = <0>;

		#address-cells = <0>;

                interrupt-parent = <&mdm0>;

                interrupts = <0 1 2 3>;

                #interrupt-cells = <1>;

                interrupt-map-mask = <0xffffffff>;

                interrupt-map =

			<0 &msmgpio 82 0x3

			1 &msmgpio 46 0x3

			2 &msmgpio 80 0x3

			3 &msmgpio 27 0x3>;

                interrupt-names =

			"err_fatal_irq",

			"status_irq",

			"plbrdy_irq",

			"mdm2ap_vddmin_irq";

                qcom,mdm2ap-errfatal-gpio = <&msmgpio 82 0x00>;

		qcom,ap2mdm-errfatal-gpio = <&msmgpio 106 0x00>;

		qcom,mdm2ap-status-gpio   = <&msmgpio 46 0x00>;

		qcom,ap2mdm-status-gpio   = <&msmgpio 105 0x00>;

		qcom,ap2mdm-soft-reset-gpio = <&msmgpio 24 0x00>;

		qcom,mdm2ap-pblrdy-gpio = <&msmgpio 80 0x00>;

		qcom,ap2mdm-wakeup-gpio = <&msmgpio 104 0x00>;

		qcom,ap2mdm-vddmin-gpio = <&msmgpio 108 0x00>;

		qcom,mdm2ap-vddmin-gpio = <&msmgpio 27 0x00>;

                qcom,ramdump-delay-ms = <2000>;

                qcom,ramdump-timeout-ms = <120000>;

                qcom,vddmin-modes  = "normal";

                qcom,vddmin-drive-strength = <8>;

		qcom,ssctl-instance-id = <10>;

		qcom,sysmon-id = <20>;

        };

source "drivers/rtc/Kconfig"

source "drivers/esoc/Kconfig"

source "drivers/dma/Kconfig"

source "drivers/dma-buf/Kconfig"

obj-$(CONFIG_STM)		+= hwtracing/stm/

obj-$(CONFIG_ANDROID)		+= android/

obj-$(CONFIG_NVMEM)		+= nvmem/

obj-$(CONFIG_ESOC)              += esoc/

obj-$(CONFIG_FPGA)		+= fpga/

#

# External soc control infrastructure and drivers

#

menuconfig ESOC

	bool "External SOCs Control"

	help

	  External SOCs can be powered on and monitored by user

	  space or kernel drivers. Additionally they can be controlled

	  to respond to control commands. This framework provides an

	  interface to track events related to the external slave socs.

if ESOC

config ESOC_DEV

	bool "ESOC userspace interface"

	help

	  Say yes here to enable a userspace representation of the control

	  link. Userspace can register a request engine or a command engine

	  for the external soc. It can receive event notifications from the

	  control link.

config ESOC_CLIENT

	bool "ESOC client interface"

	depends on OF

	help

	  Say yes here to enable client interface for external socs.

	  Clients can specify the external soc that they are interested in

	  by using device tree phandles. Based on this, clients can register

	  for notifications from a specific soc.

config ESOC_DEBUG

	bool "ESOC debug support"

	help

	  Say yes here to enable debugging support in the ESOC framework

	  and individual esoc drivers.

	  If you wish to debug the esoc driver and enable more logging enable

	  this option. Based on this, DEBUG macro would be defined which will

	  allow logging of different esoc driver traces.

config ESOC_MDM_4x

	bool "Add support for external mdm9x25/mdm9x35/mdm9x45/mdm9x55"

	help

	  In some Qualcomm Technologies, Inc. boards, an external modem such as

	  mdm9x25 or mdm9x35 is connected to a primary msm. The primary soc can

	  control/monitor the modem via gpios. The data communication with such

	  modems can occur over PCIE or HSIC.

config ESOC_MDM_DRV

	tristate "Command engine for 4x series external modems"

	help

	  Provides a command engine to control the behavior of an external modem

	  such as mdm9x25/mdm9x35/mdm9x45/mdm9x55/QSC. Allows the primary soc to put the

	  external modem in a specific mode. Also listens for events on the

	  external modem.

endif

# generic  external soc control support

ccflags-$(CONFIG_ESOC_DEBUG)	:= -DDEBUG

obj-$(CONFIG_ESOC)	+= esoc_bus.o

obj-$(CONFIG_ESOC_DEV)	+= esoc_dev.o

obj-$(CONFIG_ESOC_CLIENT)	+= esoc_client.o

obj-$(CONFIG_ESOC_MDM_4x)	+= esoc-mdm-pon.o esoc-mdm-4x.o

obj-$(CONFIG_ESOC_MDM_DRV)	+= esoc-mdm-drv.o