slimbus: Add snapshot of slimbus driver.

 Qualcomm Technologies,Inc SLIMBUS controller

 Qualcomm Technologies,Inc implements 2 type of slimbus controllers:

1. "qcom,slim-msm": This controller is used if applications processor

	driver is controlling slimbus master component. This driver is

	responsible for communicating with slave HW directly using

	messaging interface, and doing data channel management. Driver

	also communicates with satellite component (driver implemented

	by other execution environment, such as ADSP) to get its

	requirements for data channel and bandwidth requirements.

2. "qcom,slim-ngd": This controller is used if applications processor

	driver is controlling slimbus satellite component (also known as

	Non-ported Generic Device, or NGD). This is light-weight slimbus

	controller responsible for communicating with slave HW directly

	over bus messaging interface, and communicating with master component

	(driver residing on other execution environment, such as ADSP)

	for bandwidth and data channel management.

Required properties:

 - reg : Offset and length of the register region(s) for the device

 - reg-names : Register region name(s) referenced in reg above

	 Required register resource entries are:

	 "slimbus_physical": Physical adderss of controller register blocks

	 "slimbus_bam_physical": Physical address of Bus Access Module (BAM)

				 for this controller

 - compatible : should be "qcom,slim-msm" if this is master component driver

 - compatible : should be "qcom,slim-ngd" if this is satellite component driver

 - cell-index : SLIMBUS number used for this controller

 - interrupts : Interrupt numbers used by this controller

 - interrupt-names : Required interrupt resource entries are:

	"slimbus_irq" : Interrupt for SLIMBUS core

	"slimbus_bam_irq" : Interrupt for controller core's BAM

Optional property:

 - reg entry for slew rate : If slew rate control register is provided, this

	 entry should be used.

 - reg-name for slew rate: "slimbus_slew_reg"

 - qcom,min-clk-gear : Minimum clock gear at which this controller can be run

		 (range: 1-10)

		 Default value will be 1 if this entry is not specified

 - qcom,max-clk-gear: Maximum clock gear at which this controller can be run

		 (range: 1-10)

		 Default value will be 10 if this entry is not specified

 - qcom,rxreg-access: This boolean indicates that slimbus RX should use direct

		 register access to receive data. This flag is only needed if

		 BAM pipe is not available to receive data from slimbus

 - qcom,apps-ch-pipes: This value represents BAM pipe-mask used by application

		 processor for data channels. If this property is not defined,

		 default mask of 0x3F000000 is used indicating apps can use 6

		 pipes from 24-29.

 - qcom,ea-pc: This value represents product code (PC) field of enumeration

		 address (EA) for the QTI slimbus controller hardware.

		 This value is needed if data-channels originating from apps

		 are to be used, so that application processor can query

		 logical address of the ported generic device to be used.

		 Other than PC, fields of EA are same across platforms.

 - qcom,slim-mdm: This value provides the identifier of slimbus component on

		 external mdm. This property enables the slimbus driver to

		 register and receive subsytem restart notification from mdm

		 and follow appropriate steps to ensure communication on the bus

		 can be resumed after mdm-restart.

 - qcom,subsys-name: This value provides the subsystem name where slimbus master

		 is present. This property enables the slimbus driver to

		 register and receive subsytem restart notification from subsystem

		 and follow appropriate steps to ensure communication on the bus

		 can be resumed after subsytem restart. By default slimbus driver

		 register with ADSP subsystem.

Example:

	slim@fe12f000 {

		cell-index = <1>;

		compatible = "qcom,slim-msm";

		reg = <0xfe12f000 0x35000>,

		      <0xfe104000 0x20000>;

		reg-names = "slimbus_physical", "slimbus_bam_physical";

		interrupts = <0 163 0 0 164 0>;

		interrupt-names = "slimbus_irq", "slimbus_bam_irq";

		qcom,min-clk-gear = <10>;

		qcom,rxreg-access;

		qcom,apps-ch-pipes = <0x60000000>;

		qcom,ea-pc = <0x30>;

	};

source "drivers/spi/Kconfig"

source "drivers/slimbus/Kconfig"

source "drivers/spmi/Kconfig"

source "drivers/hsi/Kconfig"

obj-$(CONFIG_MTD)		+= mtd/

obj-$(CONFIG_SPI)		+= spi/

obj-$(CONFIG_SPMI)		+= spmi/

obj-$(CONFIG_SOUNDWIRE)		+= soundwire/

obj-$(CONFIG_SLIMBUS)		+= slimbus/

obj-$(CONFIG_HSI)		+= hsi/

obj-y				+= net/

obj-$(CONFIG_ATM)		+= atm/

config OF_RESOLVE

	bool

config OF_SLIMBUS

	def_tristate SLIMBUS

	depends on SLIMBUS

	help

	  OpenFirmware SLIMBUS accessors

config OF_OVERLAY

	bool "Device Tree overlays"

	select OF_DYNAMIC

obj-$(CONFIG_OF_RESERVED_MEM) += of_reserved_mem.o

obj-$(CONFIG_OF_RESOLVE)  += resolver.o

obj-$(CONFIG_OF_OVERLAY) += overlay.o

obj-$(CONFIG_OF_SLIMBUS)        += of_slimbus.o

obj-$(CONFIG_OF_NUMA) += of_numa.o

obj-$(CONFIG_OF_UNITTEST) += unittest-data/