Loading Documentation/devicetree/bindings/pinctrl/qcom,msm8937-pinctrl.txt 0 → 100644 +204 −0 Original line number Diff line number Diff line Qualcomm Technologies, Inc. MSM8937 TLMM block This binding describes the Top Level Mode Multiplexer block found in the MSM8937 platform. - compatible: Usage: required Value type: <string> Definition: must be "qcom,msm8937-pinctrl" - reg: Usage: required Value type: <prop-encoded-array> Definition: the base address and size of the TLMM register space. - interrupts: Usage: required Value type: <prop-encoded-array> Definition: should specify the TLMM summary IRQ. - interrupt-controller: Usage: required Value type: <none> Definition: identifies this node as an interrupt controller - #interrupt-cells: Usage: required Value type: <u32> Definition: must be 2. Specifying the pin number and flags, as defined in <dt-bindings/interrupt-controller/irq.h> - gpio-controller: Usage: required Value type: <none> Definition: identifies this node as a gpio controller - #gpio-cells: Usage: required Value type: <u32> Definition: must be 2. Specifying the pin number and flags, as defined in <dt-bindings/gpio/gpio.h> Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for a general description of GPIO and interrupt bindings. Please refer to pinctrl-bindings.txt in this directory for details of the common pinctrl bindings used by client devices, including the meaning of the phrase "pin configuration node". The pin configuration nodes act as a container for an arbitrary number of subnodes. Each of these subnodes represents some desired configuration for a pin, a group, or a list of pins or groups. This configuration can include the mux function to select on those pin(s)/group(s), and various pin configuration parameters, such as pull-up, drive strength, etc. PIN CONFIGURATION NODES: The name of each subnode is not important; all subnodes should be enumerated and processed purely based on their content. Each subnode only affects those parameters that are explicitly listed. In other words, a subnode that lists a mux function but no pin configuration parameters implies no information about any pin configuration parameters. Similarly, a pin subnode that describes a pullup parameter implies no information about e.g. the mux function. The following generic properties as defined in pinctrl-bindings.txt are valid to specify in a pin configuration subnode: - pins: Usage: required Value type: <string-array> Definition: List of gpio pins affected by the properties specified in this subnode. Valid pins are: gpio0-gpio133, sdc1_clk, sdc1_cmd, sdc1_data, sdc1_rclk, sdc2_clk, sdc2_cmd, sdc2_data, qdsd_clk, qdsd_cmd, qdsd_data0, qdsd_data1, qdsd_data2, qdsd_data3, - function: Usage: required Value type: <string> Definition: Specify the alternative function to be configured for the specified pins. Functions are only valid for gpio pins. Valid values are: qdss_tracedata_b, blsp_uart1, gpio, blsp_spi1, adsp_ext, blsp_i2c1, prng_rosc, qdss_cti_trig_out_b0, blsp_spi2, blsp_uart2, blsp_uart3, pbs0, pbs1, pwr_modem_enabled_b, blsp_i2c3, gcc_gp2_clk_b, ldo_update, atest_combodac_to_gpio_native, ldo_en, blsp_i2c2, gcc_gp1_clk_b, pbs2, atest_gpsadc_dtest0_native, blsp_spi3, gcc_gp3_clk_b, blsp_spi4, blsp_uart4, sec_mi2s, pwr_nav_enabled_b, codec_mad, pwr_crypto_enabled_b, blsp_i2c4, blsp_spi5, blsp_uart5, qdss_traceclk_a, atest_bbrx1, m_voc, qdss_cti_trig_in_a0, qdss_cti_trig_in_b0, blsp_i2c6, qdss_traceclk_b, atest_wlan0, atest_wlan1, atest_bbrx0, blsp_i2c5, qdss_tracectl_a, atest_gpsadc_dtest1_native, qdss_tracedata_a, blsp_spi6, blsp_uart6, qdss_tracectl_b, mdp_vsync, pri_mi2s_mclk_a, sec_mi2s_mclk_a, cam_mclk, cci_i2c, pwr_modem_enabled_a, cci_timer0, cci_timer1, cam1_standby, pwr_nav_enabled_a, cam1_rst, pwr_crypto_enabled_a, forced_usb, qdss_cti_trig_out_b1, cam2_rst, webcam_standby, cci_async, webcam_rst, ov_ldo, sd_write, accel_int, gcc_gp1_clk_a, alsp_int, gcc_gp2_clk_a, mag_int, gcc_gp3_clk_a, blsp6_spi, fp_int, qdss_cti_trig_in_b1, uim_batt, cam2_standby, uim1_data, uim1_clk, uim1_reset, uim1_present, uim2_data, uim2_clk, uim2_reset, uim2_present, sensor_rst, mipi_dsi0, smb_int, cam0_ldo, us_euro, atest_char3, dbg_out, bimc_dte0, ts_resout, ts_sample, sec_mi2s_mclk_b, pri_mi2s, sdcard_det, atest_char1, ebi_cdc, audio_reset, atest_char0, audio_ref, cdc_pdm0, pri_mi2s_mclk_b, lpass_slimbus, lpass_slimbus0, lpass_slimbus1, codec_int1, codec_int2, wcss_bt, atest_char2, ebi_ch0, wcss_wlan2, wcss_wlan1, wcss_wlan0, wcss_wlan, wcss_fm, ext_lpass, cri_trng, cri_trng1, cri_trng0, blsp_spi7, blsp_uart7, pri_mi2s_ws, blsp_i2c7, gcc_tlmm, dmic0_clk, dmic0_data, key_volp, qdss_cti_trig_in_a1, us_emitter, wsa_irq, wsa_io, wsa_reset, blsp_spi8, blsp_uart8, blsp_i2c8, gcc_plltest, nav_pps_in_a, pa_indicator, modem_tsync, nav_tsync, nav_pps_in_b, nav_pps, gsm0_tx, atest_char, atest_tsens, bimc_dte1, ssbi_wtr1, fp_gpio, coex_uart, key_snapshot, key_focus, nfc_pwr, blsp8_spi, qdss_cti_trig_out_a0, qdss_cti_trig_out_a1 - bias-disable: Usage: optional Value type: <none> Definition: The specified pins should be configued as no pull. - bias-pull-down: Usage: optional Value type: <none> Definition: The specified pins should be configued as pull down. - bias-pull-up: Usage: optional Value type: <none> Definition: The specified pins should be configued as pull up. - output-high: Usage: optional Value type: <none> Definition: The specified pins are configured in output mode, driven high. Not valid for sdc pins. - output-low: Usage: optional Value type: <none> Definition: The specified pins are configured in output mode, driven low. Not valid for sdc pins. - drive-strength: Usage: optional Value type: <u32> Definition: Selects the drive strength for the specified pins, in mA. Valid values are: 2, 4, 6, 8, 10, 12, 14 and 16 Example: tlmm: pinctrl@1000000 { compatible = "qcom,msm8937-pinctrl"; reg = <0x1000000 0x300000>; interrupts = <0 208 0>; gpio-controller; #gpio-cells = <2>; interrupt-controller; #interrupt-cells = <2>; pmx-uartconsole { uart_console_active: uart_console_active { mux { pins = "gpio4", "gpio5"; function = "blsp_uart2"; }; config { pins = "gpio4", "gpio5"; drive-strength = <2>; bias-disable; }; }; uart_console_sleep: uart_console_sleep { mux { pins = "gpio4", "gpio5"; function = "blsp_uart2"; }; config { pins = "gpio4", "gpio5"; drive-strength = <2>; bias-pull-down; }; }; }; }; arch/arm64/Kconfig.platforms +9 −0 Original line number Diff line number Diff line Loading @@ -154,6 +154,15 @@ config ARCH_MSM8953 This enables support for the MSM8953 chipset. If you do not wish to build a kernel that runs on this chipset, say 'N' here. config ARCH_MSM8937 bool "Enable Support for Qualcomm Technologies Inc. MSM8937" depends on ARCH_QCOM select CPU_FREQ_QCOM select COMMON_CLK_MSM help This enables support for the MSM8937 chipset. If you do not wish to build a kernel that runs on this chipset, say 'N' here. config ARCH_SDM450 bool "Enable Support for Qualcomm Technologies Inc. SDM450" depends on ARCH_QCOM Loading arch/arm64/configs/msm8953-perf_defconfig +1 −0 Original line number Diff line number Diff line Loading @@ -52,6 +52,7 @@ CONFIG_PARTITION_ADVANCED=y # CONFIG_IOSCHED_DEADLINE is not set CONFIG_ARCH_QCOM=y CONFIG_ARCH_MSM8953=y CONFIG_ARCH_MSM8937=y CONFIG_ARCH_SDM450=y CONFIG_ARCH_SDM632=y CONFIG_SCHED_MC=y Loading arch/arm64/configs/msm8953_defconfig +1 −0 Original line number Diff line number Diff line Loading @@ -56,6 +56,7 @@ CONFIG_PARTITION_ADVANCED=y # CONFIG_IOSCHED_DEADLINE is not set CONFIG_ARCH_QCOM=y CONFIG_ARCH_MSM8953=y CONFIG_ARCH_MSM8937=y CONFIG_ARCH_SDM450=y CONFIG_ARCH_SDM632=y CONFIG_SCHED_MC=y Loading drivers/pinctrl/qcom/Kconfig +10 −0 Original line number Diff line number Diff line Loading @@ -89,6 +89,16 @@ config PINCTRL_MSM8953 Technologies Inc MSM8953 platform. If unsure say N. config PINCTRL_MSM8937 tristate "Qualcomm Technologies Inc MSM8937 pin controller driver" depends on GPIOLIB && OF select PINCTRL_MSM help This is the pinctrl, pinmux, pinconf and gpiolib driver for the Qualcomm Technologies Inc TLMM block found on the Qualcomm Technologies Inc MSM8937 platform. If unsure say N. config PINCTRL_SDM845 tristate "Qualcomm Technologies Inc SDM845 pin controller driver" depends on GPIOLIB && OF Loading Loading
Documentation/devicetree/bindings/pinctrl/qcom,msm8937-pinctrl.txt 0 → 100644 +204 −0 Original line number Diff line number Diff line Qualcomm Technologies, Inc. MSM8937 TLMM block This binding describes the Top Level Mode Multiplexer block found in the MSM8937 platform. - compatible: Usage: required Value type: <string> Definition: must be "qcom,msm8937-pinctrl" - reg: Usage: required Value type: <prop-encoded-array> Definition: the base address and size of the TLMM register space. - interrupts: Usage: required Value type: <prop-encoded-array> Definition: should specify the TLMM summary IRQ. - interrupt-controller: Usage: required Value type: <none> Definition: identifies this node as an interrupt controller - #interrupt-cells: Usage: required Value type: <u32> Definition: must be 2. Specifying the pin number and flags, as defined in <dt-bindings/interrupt-controller/irq.h> - gpio-controller: Usage: required Value type: <none> Definition: identifies this node as a gpio controller - #gpio-cells: Usage: required Value type: <u32> Definition: must be 2. Specifying the pin number and flags, as defined in <dt-bindings/gpio/gpio.h> Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for a general description of GPIO and interrupt bindings. Please refer to pinctrl-bindings.txt in this directory for details of the common pinctrl bindings used by client devices, including the meaning of the phrase "pin configuration node". The pin configuration nodes act as a container for an arbitrary number of subnodes. Each of these subnodes represents some desired configuration for a pin, a group, or a list of pins or groups. This configuration can include the mux function to select on those pin(s)/group(s), and various pin configuration parameters, such as pull-up, drive strength, etc. PIN CONFIGURATION NODES: The name of each subnode is not important; all subnodes should be enumerated and processed purely based on their content. Each subnode only affects those parameters that are explicitly listed. In other words, a subnode that lists a mux function but no pin configuration parameters implies no information about any pin configuration parameters. Similarly, a pin subnode that describes a pullup parameter implies no information about e.g. the mux function. The following generic properties as defined in pinctrl-bindings.txt are valid to specify in a pin configuration subnode: - pins: Usage: required Value type: <string-array> Definition: List of gpio pins affected by the properties specified in this subnode. Valid pins are: gpio0-gpio133, sdc1_clk, sdc1_cmd, sdc1_data, sdc1_rclk, sdc2_clk, sdc2_cmd, sdc2_data, qdsd_clk, qdsd_cmd, qdsd_data0, qdsd_data1, qdsd_data2, qdsd_data3, - function: Usage: required Value type: <string> Definition: Specify the alternative function to be configured for the specified pins. Functions are only valid for gpio pins. Valid values are: qdss_tracedata_b, blsp_uart1, gpio, blsp_spi1, adsp_ext, blsp_i2c1, prng_rosc, qdss_cti_trig_out_b0, blsp_spi2, blsp_uart2, blsp_uart3, pbs0, pbs1, pwr_modem_enabled_b, blsp_i2c3, gcc_gp2_clk_b, ldo_update, atest_combodac_to_gpio_native, ldo_en, blsp_i2c2, gcc_gp1_clk_b, pbs2, atest_gpsadc_dtest0_native, blsp_spi3, gcc_gp3_clk_b, blsp_spi4, blsp_uart4, sec_mi2s, pwr_nav_enabled_b, codec_mad, pwr_crypto_enabled_b, blsp_i2c4, blsp_spi5, blsp_uart5, qdss_traceclk_a, atest_bbrx1, m_voc, qdss_cti_trig_in_a0, qdss_cti_trig_in_b0, blsp_i2c6, qdss_traceclk_b, atest_wlan0, atest_wlan1, atest_bbrx0, blsp_i2c5, qdss_tracectl_a, atest_gpsadc_dtest1_native, qdss_tracedata_a, blsp_spi6, blsp_uart6, qdss_tracectl_b, mdp_vsync, pri_mi2s_mclk_a, sec_mi2s_mclk_a, cam_mclk, cci_i2c, pwr_modem_enabled_a, cci_timer0, cci_timer1, cam1_standby, pwr_nav_enabled_a, cam1_rst, pwr_crypto_enabled_a, forced_usb, qdss_cti_trig_out_b1, cam2_rst, webcam_standby, cci_async, webcam_rst, ov_ldo, sd_write, accel_int, gcc_gp1_clk_a, alsp_int, gcc_gp2_clk_a, mag_int, gcc_gp3_clk_a, blsp6_spi, fp_int, qdss_cti_trig_in_b1, uim_batt, cam2_standby, uim1_data, uim1_clk, uim1_reset, uim1_present, uim2_data, uim2_clk, uim2_reset, uim2_present, sensor_rst, mipi_dsi0, smb_int, cam0_ldo, us_euro, atest_char3, dbg_out, bimc_dte0, ts_resout, ts_sample, sec_mi2s_mclk_b, pri_mi2s, sdcard_det, atest_char1, ebi_cdc, audio_reset, atest_char0, audio_ref, cdc_pdm0, pri_mi2s_mclk_b, lpass_slimbus, lpass_slimbus0, lpass_slimbus1, codec_int1, codec_int2, wcss_bt, atest_char2, ebi_ch0, wcss_wlan2, wcss_wlan1, wcss_wlan0, wcss_wlan, wcss_fm, ext_lpass, cri_trng, cri_trng1, cri_trng0, blsp_spi7, blsp_uart7, pri_mi2s_ws, blsp_i2c7, gcc_tlmm, dmic0_clk, dmic0_data, key_volp, qdss_cti_trig_in_a1, us_emitter, wsa_irq, wsa_io, wsa_reset, blsp_spi8, blsp_uart8, blsp_i2c8, gcc_plltest, nav_pps_in_a, pa_indicator, modem_tsync, nav_tsync, nav_pps_in_b, nav_pps, gsm0_tx, atest_char, atest_tsens, bimc_dte1, ssbi_wtr1, fp_gpio, coex_uart, key_snapshot, key_focus, nfc_pwr, blsp8_spi, qdss_cti_trig_out_a0, qdss_cti_trig_out_a1 - bias-disable: Usage: optional Value type: <none> Definition: The specified pins should be configued as no pull. - bias-pull-down: Usage: optional Value type: <none> Definition: The specified pins should be configued as pull down. - bias-pull-up: Usage: optional Value type: <none> Definition: The specified pins should be configued as pull up. - output-high: Usage: optional Value type: <none> Definition: The specified pins are configured in output mode, driven high. Not valid for sdc pins. - output-low: Usage: optional Value type: <none> Definition: The specified pins are configured in output mode, driven low. Not valid for sdc pins. - drive-strength: Usage: optional Value type: <u32> Definition: Selects the drive strength for the specified pins, in mA. Valid values are: 2, 4, 6, 8, 10, 12, 14 and 16 Example: tlmm: pinctrl@1000000 { compatible = "qcom,msm8937-pinctrl"; reg = <0x1000000 0x300000>; interrupts = <0 208 0>; gpio-controller; #gpio-cells = <2>; interrupt-controller; #interrupt-cells = <2>; pmx-uartconsole { uart_console_active: uart_console_active { mux { pins = "gpio4", "gpio5"; function = "blsp_uart2"; }; config { pins = "gpio4", "gpio5"; drive-strength = <2>; bias-disable; }; }; uart_console_sleep: uart_console_sleep { mux { pins = "gpio4", "gpio5"; function = "blsp_uart2"; }; config { pins = "gpio4", "gpio5"; drive-strength = <2>; bias-pull-down; }; }; }; };
arch/arm64/Kconfig.platforms +9 −0 Original line number Diff line number Diff line Loading @@ -154,6 +154,15 @@ config ARCH_MSM8953 This enables support for the MSM8953 chipset. If you do not wish to build a kernel that runs on this chipset, say 'N' here. config ARCH_MSM8937 bool "Enable Support for Qualcomm Technologies Inc. MSM8937" depends on ARCH_QCOM select CPU_FREQ_QCOM select COMMON_CLK_MSM help This enables support for the MSM8937 chipset. If you do not wish to build a kernel that runs on this chipset, say 'N' here. config ARCH_SDM450 bool "Enable Support for Qualcomm Technologies Inc. SDM450" depends on ARCH_QCOM Loading
arch/arm64/configs/msm8953-perf_defconfig +1 −0 Original line number Diff line number Diff line Loading @@ -52,6 +52,7 @@ CONFIG_PARTITION_ADVANCED=y # CONFIG_IOSCHED_DEADLINE is not set CONFIG_ARCH_QCOM=y CONFIG_ARCH_MSM8953=y CONFIG_ARCH_MSM8937=y CONFIG_ARCH_SDM450=y CONFIG_ARCH_SDM632=y CONFIG_SCHED_MC=y Loading
arch/arm64/configs/msm8953_defconfig +1 −0 Original line number Diff line number Diff line Loading @@ -56,6 +56,7 @@ CONFIG_PARTITION_ADVANCED=y # CONFIG_IOSCHED_DEADLINE is not set CONFIG_ARCH_QCOM=y CONFIG_ARCH_MSM8953=y CONFIG_ARCH_MSM8937=y CONFIG_ARCH_SDM450=y CONFIG_ARCH_SDM632=y CONFIG_SCHED_MC=y Loading
drivers/pinctrl/qcom/Kconfig +10 −0 Original line number Diff line number Diff line Loading @@ -89,6 +89,16 @@ config PINCTRL_MSM8953 Technologies Inc MSM8953 platform. If unsure say N. config PINCTRL_MSM8937 tristate "Qualcomm Technologies Inc MSM8937 pin controller driver" depends on GPIOLIB && OF select PINCTRL_MSM help This is the pinctrl, pinmux, pinconf and gpiolib driver for the Qualcomm Technologies Inc TLMM block found on the Qualcomm Technologies Inc MSM8937 platform. If unsure say N. config PINCTRL_SDM845 tristate "Qualcomm Technologies Inc SDM845 pin controller driver" depends on GPIOLIB && OF Loading
