Merge "power: qpnp-smbcharger: Add snapshot of qpnp-smbcharger driver"

QPNP SMB Battery Charger

QPNP SMB Charger is a single-cell switching mode battery charger. It can charge

the battery and power the system via the USB and AC adapter input.

The QPNP SMB Charger interfaces via the SPMI bus.

There are six different peripherals adding the following functionality.

Each of these peripherals are implemented as subnodes in the example at the

end of this file.

- qcom,chgr:		Supports charging control and status

			reporting.

- qcom,bat-if:		Battery status reporting such as presence,

			temperature reporting and voltage collapse

			protection.

- qcom,usb-chgpth:	USB charge path detection and input current

			limiting configuration.

- qcom,dc-chgpth:	DC charge path detection and input current

			limiting configuration.

- qcom,chg-misc:	Miscellaneous features such as watchdog timers

			and SYSOK pin control

- qcom,chg-otg:		OTG configuration control.

Parent node required properties:

- compatible:		Must be "qcom,qpnp-smbcharger"

- #address-cells:	Must be <1>

- #size-cells:		Must be <1>

- qcom,pmic-revid:      Should specify the phandle of PMIC

                        revid module. This is used to identify

                        the PMIC subtype.

Sub node required properties:

- reg:			The SPMI address for this peripheral

- interrupts:		Specifies the interrupt associated with the peripheral.

- interrupt-names:	Specifies the interrupt names for the peripheral. Every

			available interrupt needs to have an associated name

			with it to indentify its purpose.

			The following lists each subnode and their corresponding

			required interrupt names:

			qcom,chgr:

			 - chg-tcc-thr:		Triggers on charge completion.

			 - chg-taper-thr:	Triggers on the taper charge

						transtion.

			 - chg-inhibit:		Notifies on battery voltage

						being too high to resume

						charging.

			 - chg-p2f-thr:		Triggers on transitioning from

						precharge to fastcharge.

			 - chg-rechg-thr:	Triggers on battery voltage

						falling below the resume

						threshold.

			qcom,bat-if:

			 - batt-hot:		Triggers on battery temperature

						hitting the hot threshold.

						Charging stops.

			 - batt-warm:		Triggers on battery temperature

						hitting the warm threshold.

						Charging current is reduced.

			 - batt-cool:		Triggers on battery temperature

						hitting the cool threshold.

						Charging current is reduced

			 - batt-cold:		Triggers on battery temperature

						hitting the cold threshold.

						Charging stops.

			 - batt-missing:	Battery missing status

						interrupt.

			 - batt-low:		Triggers on battery voltage

						falling across a low threshold.

			qcom,usb-chgpth:

			 - usbin-uv:		USB input voltage falls below a

						valid threshold.

			 - usbin-src-det:	USB automatic source detection

						finishes.

			qcom,dc-chgpth:

			 - dcin-uv:		DC input voltage falls below a

						valid threshold.

			qcom,chgr-misc:

			 - wdog-timeout-mins:	Charger watchdog timer

						interrupt.

			 - temp-shutdown:	Triggers when charger goes

						overtemp and causes a shutdown.

			 - power-ok:		Triggers when the charger

						switcher turns on or off.

Regulator Subnodes:

- qcom,smbcharger-boost-otg	A subnode for a regulator device that turns on

				the charger boost for OTG operation.

- qcom,smbcharger-external-otg	A subnode for a regulator device that switches

				off charging and the USB input charge path

				in order to allow an external regulator to

				operate. This can be used in place of the

				qcom,smbcharger-boost-otg if an external boost

				is available.

Regulator Sub node required properties:

- regulator-name		A name string for the regulator in question

Optional Properties:

- qcom,battery-psy-name		The name of the main battery power supply that

				the charger will register. Failing to define

				this property will default the name to

				"battery".

- qcom,bms-psy-name		The psy name to use for reporting battery

				capacity. If left unspecified the capacity uses

				a preprogrammed default value of 50.

- qcom,float-voltage-mv		Float Voltage in mV - the maximum voltage up

				to which the battery is charged. Supported

				range 3600mV to 4500mV

- qcom,float-voltage-comp	Specifies the JEITA float voltage compensation.

				Value ranges from 0 to 63.

- qcom,fastchg-current-ma	Specifies the fast charge current in mA. Supported

				range is from 300mA to 3000mA.

- qcom,fastchg-current-comp	Specifies the fast charge current compensation in

				mA. Supported values are 250, 700, 900 and 1200mA.

- qcom,charging-timeout-mins	Maximum duration in minutes that a single

				charge cycle may last.  Supported values are:

				0, 192, 384, 768, and 1536.  A value of 0

				means that no charge cycle timeout is used and

				charging can continue indefinitely.

- qcom,precharging-timeout-mins	Maximum duration in minutes that a single

				precharge cycle may last.  Supported values

				are: 0, 24, 48, 96, 192.  A value of 0 means

				that no precharge cycle timeout is used and

				charging can continue indefinitely. Note that

				the qcom,charging-timeout-mins property must

				be specified in order for this to take effect.

- qcom,dc-psy-type		The type of charger connected to the DC path.

				Can be "Mains", "Wireless" or "Wipower"

- qcom,dc-psy-ma		The current in mA dc path can support. Must be

				specified if dc-psy-type is specified. Valid

				range 300mA to 2000mA.

- qcom,dcin-vadc		The phandle to pmi8994 voltage adc. The ADC is

				used to get notifications when the DCIN voltage

				crosses a programmed min/max threshold. This is

				used to make configurations for optimized power

				draw for Wipower.

- qcom,wipower-div2-ilim-map

- qcom,wipower-pt-ilim-map

- qcom,wipower-default-ilim-map

				Array of 5 elements to indicate the voltage ranges and their corresponding

				current limits. The 5 elements with index [0..4] are:

				[0] => voltage_low in uV

				[1] => voltage_high in uV

				[2] => current limit for pass through in mA

				[3] => current limit for div2 mode dcin low voltage in mA

				[4] => current limit for div2 mode dcin high voltage in mA

				The div2 and pt tables indicate the current limits

				to use when Wipower is operating in divide_by_2 mode

				and pass through mode respectively.

				The default table is used when the voltage ranges

				are beyond the ones specified in the mapping table.

				Note that if dcin-vadc or any of these mapping

				tables are not specified, dynamic dcin input

				is disabled.

- qcom,charging-disabled	Set this if charging should be disabled in the

				build by default.

- qcom,resume-delta-mv		Specifies the minimum voltage drop in

				millivolts below the float voltage that is

				required in order to initiate a new charging

				cycle. Supported values are: 50, 100, 200 and

				300mV.

- qcom,chg-inhibit-en		Boolean that indicates whether the charge inhibit

				feature needs to be enabled. If this is not set,

				charge inhibit feature is disabled by default.

- qcom,chg-inhibit-fg		Indicates if the recharge threshold source has

				to be Fuel gauge ADC. If this is not set, it

				will be analog sensor by default.

- qcom,bmd-algo-disabled	Indicates if the battery missing detection

				algorithm is disabled. If this node is present

				SMB uses the THERM pin for battery missing

				detection.

- qcom,charge-unknown-battery	Boolean that indicates whether an unknown

				battery without a matching profile will be

				charged. If this is not set, if the fuel gauge

				does not recognize the battery based on its

				battery ID, the charger will not start

				charging.

- qcom,bmd-pin-src		A string that indicates the source pin for the

				battery missind detection. This can be either:

				- "bpd_none"

					battery is considered always present

				- "bpd_id"

					battery id pin is used

				- "bpd_thm"

					battery therm pin is used

				- "bpd_thm_id"

					both pins are used (battery is

					considered missing if either pin is

					floating).

- qcom,iterm-ma			Specifies the termination current to indicate

				end-of-charge. Possible values in mA:

				50, 100, 150, 200, 250, 300, 500, 600.

- qcom,iterm-disabled		Disables the termination current feature. This

				is a boolean property.

- otg-parent-supply		A phandle to an external boost regulator for

				OTG if it exists.

- qcom,thermal-mitigation:	Array of input current limit values for

				different system thermal mitigation levels.

				This should be a flat array that denotates the

				maximum charge current in mA for each thermal

				level.

- qcom,rparasitics-uohm:	The parasitic resistance of the board following

				the line from the battery connectors through

				vph_power. This is used to calculate maximum

				available current of the battery.

- qcom,vled-max-uv:		The maximum input voltage of the flash leds.

				This is used to calculate maximum available

				current of the battery.

- qcom,autoadjust-vfloat	A boolean property that when set, makes the

				driver automatically readjust vfloat using the

				fuel gauge ADC readings to make charging more

				accurate.

- qcom,jeita-temp-hard-limit	property when present will enable or disable

				the jeita temperature hard limit based on the

				value 1 or 0. Specify 0 if the jeita temp hard

				limit needs to be disabled. If it is not present,

				jeita temperature hard limit will be based on what

				the bootloader had set earlier.

- qcom,low-volt-dcin:		A boolean property which upon set will enable the

				AICL deglitch configuration dynamically. This needs

				to be set if the DCIN supply is going to be less

				than or equal to 5V.

- qcom,force-aicl-rerun:	A boolean property which upon set will enable the

				AICL rerun by default along with the deglitch time

				configured to long interval (20 ms). Also, specifying

				this property will not adjust the AICL deglitch time

				dynamically for handling the battery over-voltage

				oscillations when the charger is headroom limited.

- qcom,aicl-rerun-period-s	If force-aicl-rerun is on, this property dictates

				how often aicl is reran in seconds. Possible values

				are 45, 90, 180, and 360.

- qcom,ibat-ocp-threshold-ua	Maximum current before the battery will trigger

				overcurrent protection. Use the recommended

				battery pack value minus some margin.

- qcom,soft-vfloat-comp-disabled	Set this property when the battery is

					powered via external source and could

					go above the float voltage.

- qcom,parallel-usb-min-current-ma	Minimum current drawn by the primary

					charger before enabling the parallel

					charger if one exists. Do not define

					this property if no parallel chargers

					exist.

- qcom,parallel-usb-9v-min-current-ma	Minimum current drawn by the primary

					charger before enabling the parallel

					charger if one exists. This property

					applies only for 9V chargers.

- qcom,parallel-allowed-lowering-ma	Acceptable current drop from the initial limit

					to keep parallel charger activated. If the

					charger current reduces beyond this threshold

					parallel charger is disabled. Must be specified

					if parallel charger is used.

- qcom,parallel-main-chg-fcc-percent	Percentage of the fast charge current allotted to the

					main charger when parallel charging is enabled and

					operational. If this property is not defined, the

					driver defaults to a 50%/50% split between the main

					and parallel charger.

- qcom,parallel-main-chg-icl-percent	Percentage of the input current allotted to the

					main charger when parallel charging is enabled and

					operational. If this property is not defined, the

					driver defaults to a 60%/40% split between the main

					and parallel charger.

- qcom,battery-data			Points to the phandle of node which

					contains the battery-profiles supported

					by the charger/FG.

- qcom,chg-led-support		A bool property to support the charger led feature.

- qcom,chg-led-sw-controls		A bool property to allow the software to control

					the charger led without a valid charger.

- qcom,skip-usb-notification	A boolean property to be used when usb gets present

				and type from other means. Especially true on

				liquid hardware, where usb presence is detected based on GPIO.

- qcom,skip-usb-suspend-for-fake-battery	A boolean property to skip

						suspending USB path for fake

						battery.

- qcom,vchg_sns-vadc		Phandle of the VADC node.

- qcom,vchg-adc-channel-id	The ADC channel to which the VCHG is routed.

Example:

	qcom,qpnp-smbcharger {

		compatible = "qcom,qpnp-smbcharger";

		#address-cells = <1>;

		#size-cells = <1>;

		qcom,iterm-ma = <100>;

		qcom,float-voltage-mv = <4200>;

		qcom,resume-delta-mv = <100>;

		qcom,bmd-pin-src = "bpd_thm_id";

		qcom,dc-psy-type = "Mains";

		qcom,dc-psy-ma = <1500>;

		qcom,bms-psy-name = "bms";

		qcom,battery-psy-name = "battery";

		qcom,thermal-mitigation = <1500 700 600 325>;

		qcom,vchg_sns-vadc = <&pmi8950_vadc>;

		qcom,vchg-adc-channel-id = <3>;

		qcom,chgr@1000 {

			reg = <0x1000 0x100>;

			interrupts =	<0x2 0x10 0x0>,

					<0x2 0x10 0x1>,

					<0x2 0x10 0x2>,

					<0x2 0x10 0x3>,

					<0x2 0x10 0x4>,

					<0x2 0x10 0x5>,

					<0x2 0x10 0x6>,

					<0x2 0x10 0x7>;

			interrupt-names =	"chg-error",

						"chg-inhibit",

						"chg-prechg-sft",

						"chg-complete-chg-sft",

						"chg-p2f-thr",

						"chg-rechg-thr",

						"chg-taper-thr",

						"chg-tcc-thr";

		};

		qcom,otg@1100 {

			reg = <0x1100 0x100>;

		};

		qcom,bat-if@1200 {

			reg = <0x1200 0x100>;

			interrupts =	<0x2 0x12 0x0>,

					<0x2 0x12 0x1>,

					<0x2 0x12 0x2>,

					<0x2 0x12 0x3>,

					<0x2 0x12 0x4>,

					<0x2 0x12 0x5>,

					<0x2 0x12 0x6>,

					<0x2 0x12 0x7>;

			interrupt-names =	"batt-hot",

						"batt-warm",

						"batt-cold",

						"batt-cool",

						"batt-ov",

						"batt-low",

						"batt-missing",

						"batt-term-missing";

		};

		qcom,usb-chgpth@1300 {

			reg = <0x1300 0x100>;

			interrupts =	<0x2 0x13 0x0>,

					<0x2 0x13 0x1>,

					<0x2 0x13 0x2>,

					<0x2 0x13 0x3>,

					<0x2 0x13 0x4>,

					<0x2 0x13 0x5>,

					<0x2 0x13 0x6>;

			interrupt-names =	"usbin-uv",

						"usbin-ov",

						"usbin-src-det",

						"otg-fail",

						"otg-oc",

						"aicl-done",

						"usbid-change";

		};

		qcom,dc-chgpth@1400 {

			reg = <0x1400 0x100>;

			interrupts =	<0x2 0x14 0x0>,

					<0x2 0x14 0x1>;

			interrupt-names =	"dcin-uv",

						"dcin-ov";

		};

		qcom,chgr-misc@1600 {

			reg = <0x1600 0x100>;

			interrupts =	<0x2 0x16 0x0>,

					<0x2 0x16 0x1>,

					<0x2 0x16 0x2>,

					<0x2 0x16 0x3>,

					<0x2 0x16 0x4>,

					<0x2 0x16 0x5>;

			interrupt-names =	"power-ok",

						"temp-shutdown",

						"wdog-timeout",

						"flash-fail",

						"otst2",

						"otst3";

		};

	};

	  The driver reports the charger status via the power supply framework.

	  A charger status change triggers an IRQ via the device STAT pin.

config QPNP_SMBCHARGER

	tristate "QPNP SMB Charger driver"

	depends on MFD_SPMI_PMIC

	help

	  Say Y here to enable the dual path switch mode battery charger which

	  supports USB detection and battery charging up to 3A.

	  The driver also offers relevant information to userspace via the

	  power supply framework.

config QPNP_QNOVO

	bool "QPNP QNOVO driver"

	depends on MFD_SPMI_PMIC

obj-$(CONFIG_QPNP_FG_GEN3)     += qpnp-fg-gen3.o fg-memif.o fg-util.o

obj-$(CONFIG_QPNP_SMBCHARGER)	+= qpnp-smbcharger.o pmic-voter.o

obj-$(CONFIG_SMB135X_CHARGER)   += smb135x-charger.o pmic-voter.o

obj-$(CONFIG_SMB1355_SLAVE_CHARGER)   += smb1355-charger.o pmic-voter.o

obj-$(CONFIG_SMB1351_USB_CHARGER) += smb1351-charger.o pmic-voter.o battery.o

/*

 * Copyright (c) 2014, The Linux Foundation. All rights reserved.

 *

 * This program is free software; you can redistribute it and/or modify

 * it under the terms of the GNU General Public License version 2 and

 * only version 2 as published by the Free Software Foundation.

 *

 * This program is distributed in the hope that it will be useful,

 * but WITHOUT ANY WARRANTY; without even the implied warranty of

 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the

 * GNU General Public License for more details.

 */

#ifndef __MSM_BCL_H

#define __MSM_BCL_H

#define BCL_NAME_MAX_LEN 20

enum bcl_trip_type {

	BCL_HIGH_TRIP,

	BCL_LOW_TRIP,

	BCL_TRIP_MAX,

};

enum bcl_param {

	BCL_PARAM_VOLTAGE,

	BCL_PARAM_CURRENT,

	BCL_PARAM_MAX,

};

struct bcl_threshold {

	int                     trip_value;

	enum bcl_trip_type      type;

	void                    *trip_data;

	void (*trip_notify)     (enum bcl_trip_type, int, void *);

};

struct bcl_param_data;

struct bcl_driver_ops {

	int (*read)             (int *);

	int (*set_high_trip)    (int);

	int (*get_high_trip)    (int *);

	int (*set_low_trip)     (int);

	int (*get_low_trip)     (int *);

	int (*disable)          (void);

	int (*enable)           (void);

	int (*notify)           (struct bcl_param_data *, int,

					enum bcl_trip_type);

};

struct bcl_param_data {

	char                    name[BCL_NAME_MAX_LEN];

	struct device           device;

	struct bcl_driver_ops   *ops;

	int                     high_trip;

	int                     low_trip;

	int                     last_read_val;

	bool                    registered;

	struct kobj_attribute   val_attr;

	struct kobj_attribute   high_trip_attr;

	struct kobj_attribute   low_trip_attr;

	struct attribute_group  bcl_attr_gp;

	struct bcl_threshold    *thresh[BCL_TRIP_MAX];

};

#ifdef CONFIG_MSM_BCL_CTL

struct bcl_param_data *msm_bcl_register_param(enum bcl_param,

	struct bcl_driver_ops *, char *);

int msm_bcl_unregister_param(struct bcl_param_data *);

int msm_bcl_enable(void);

int msm_bcl_disable(void);

int msm_bcl_set_threshold(enum bcl_param, enum bcl_trip_type,

	struct bcl_threshold *);

int msm_bcl_read(enum bcl_param, int *);

#else

static inline struct bcl_param_data *msm_bcl_register_param(

	enum bcl_param param_type, struct bcl_driver_ops *ops, char *name)

{

	return NULL;

}

static inline int msm_bcl_unregister_param(struct bcl_param_data *data)

{

	return -ENOSYS;

}

static inline int msm_bcl_enable(void)

{

	return -ENOSYS;

}

static inline int msm_bcl_disable(void)

{

	return -ENOSYS;

}

static inline int msm_bcl_set_threshold(enum bcl_param param_type,

	enum bcl_trip_type type,

	struct bcl_threshold *inp_thresh)

{

	return -ENOSYS;

}

static inline int msm_bcl_read(enum bcl_param param_type, int *vbat_value)

{

	return -ENOSYS;

}

#endif

#endif /*__MSM_BCL_H*/