Merge "cnss: Add support of cnss driver"

* Qualcomm Technologies, Inc. Connectivity SubSystem Platform Driver

This platform driver adds support for the CNSS subsystem used for SDIO

based Wi-Fi devices. It also adds support to manage two 1.8V voltage

regulators and WLAN power enable 3.3V regulators. The main purpose of this

device tree entry below is to invoke the CNSS SDIO platform driver

and provide handle to the WLAN power enable 3.3V pmic GPIO and two 1.8V

PMIC voltage regulator resources.

Required properties:

  - compatible: "qcom,cnss_sdio"

  - reg: memory resource to save firmware dump, optional.

  - reg-names: memory resource name.

  - subsys-name: cnss sdio subsytem device name, required.

  - vdd-wlan-supply: phandle to the WLAN vdd regulator device tree node.

  - vdd-wlan-dsrc-supply: phandle to the WLAN dsrc vdd regulator device tree node.

  - vdd-wlan-io-supply: phandle to the WLAN IO regulator device tree node.

  - vdd-wlan-xtal-supply: phandle to the WLAM XTAL regulator device tree node.

Optional properties:

  - pinctrl-names: Names corresponding to the numbered pinctrl states

  - pinctrl-<n>: Pinctrl states as described in

                bindings/pinctrl/pinctrl-bindings.txt

  - qcom,is-antenna-shared: Enabled for Platforms with both sdio and pcie QCA

                           Chipsets are attached.

  - qcom,cnss-enable-bus-bandwidth: Boolean - Define this property when target

					support to vote for bus bandwidth.

  - qcom,msm-bus,name: client name for msm bus register.

  - qcom,msm-bus,num-cases: number of cases for bus scaling.

  - qcom,msm-bus,num-paths: number of paths for bus scale vector.

  - qcom,msm-bus,vectors-KBps: bus scale vector table.

  - qcom,skip-wlan-en-toggle: Boolean property to be enabled for platforms where

                           wlan_en toggling is not supported.

Example:

	qcom,cnss-sdio {

		compatible = "qcom,cnss_sdio";

		reg = <0x87a00000, 0x200000>;

		reg-names = "ramdump";

		subsys-name = "AR6320";

		vdd-wlan-supply = <&rome_vreg>;

		vdd-wlan-dsrc-supply = <&sdcard_ext_vreg>;

		vdd-wlan-io-supply = <&mdm9607_l11>;

		vdd-wlan-xtal-supply = <&mdm9607_l2>;

		qcom,is-antenna-shared;

		pinctrl-names = "active", "sleep";

		pinctrl-0 = <&cnss_sdio_active>;

		pinctrl-1 = <&cnss_sdio_sleep>;

		qcom,cnss-enable-bus-bandwidth;

		qcom,msm-bus,name = "msm-cnss";

		qcom,msm-bus,num-cases = <4>;

		qcom,msm-bus,num-paths = <1>;

		qcom,msm-bus,vectors-KBps =

				<79 512 0 0>,			/* No vote */

				<79 512 6250 200000>,		/* 50 Mbps */

				<79 512 25000 200000>,		/* 200 Mbps */

				<79 512 2048000 4096000>;	/* MAX */

	};

	 for it's internal usage and release it to back to pre allocated pool.

	 This memory is allocated at the cold boot time.

config CLD_LL_CORE

       tristate "QTI core WLAN driver for QCA6174 chipset"

       select NL80211_TESTMODE

       select WEXT_CORE

       select WEXT_PRIV

       select WEXT_SPY

       select WIRELESS_EXT

       ---help---

         This section contains the necessary modules needed to enable the

	 core WLAN driver for QTI QCA6174 chipset.

	 Select Y to compile the driver in order to have WLAN functionality

	 support.

source "drivers/net/wireless/cnss2/Kconfig"

source "drivers/net/wireless/cnss/Kconfig"

source "drivers/net/wireless/cnss_utils/Kconfig"

source "drivers/net/wireless/cnss_genl/Kconfig"

obj-$(CONFIG_MAC80211_HWSIM)	+= mac80211_hwsim.o

obj-$(CONFIG_CNSS2)	+= cnss2/

obj-$(CONFIG_CNSS)              += cnss/

obj-$(CONFIG_WCNSS_MEM_PRE_ALLOC) += cnss_prealloc/

obj-$(CONFIG_CNSS_UTILS) += cnss_utils/

obj-$(CONFIG_CNSS_GENL) += cnss_genl/

config CNSS

	tristate "CNSS driver for wifi module"

	select CNSS_UTILS

	select CRYPTO

	select CRYPTO_HASH

	select CRYPTO_BLKCIPHER

	---help---

	 This module adds support for the CNSS connectivity subsystem used

	 for wifi devices based on the QCA AR6320 chipset.

	 This driver also adds support to integrate WLAN module to subsystem

	 restart framework.

config CNSS_SDIO

	bool "Enable/disable cnss sdio platform driver for wifi module"

	depends on CNSS

	depends on MMC

	---help---

	 This module adds support for the CNSS wlan module interfaced

	 with SDIO bus.

	 This driver also adds support to integrate WLAN module to subsystem

	 restart framework, power on WLAN chip and registered the WLAN module

	 as a SDIO client device.

config CNSS_PCI

	bool "Enable/disable cnss pci platform driver for wifi module"

	depends on CNSS

	depends on PCI

	---help---

	 This module adds support for the CNSS wlan module interfaced

	 with PCIe bus.

	 This driver also adds support to integrate WLAN module to subsystem

	 restart framework, power on WLAN chip and registered the WLAN module

	 as a PCIe client device.

config CNSS_ASYNC

	bool "Enable/disable cnss pci platform driver asynchronous probe"

	depends on CNSS_PCI

	---help---

	 If enabled, CNSS PCI platform driver would do asynchronous probe.

	 Using asynchronous probe will allow CNSS PCI platform driver to

	 probe in parallel with other device drivers and will help to

	 reduce kernel boot time.

config CNSS_MAC_BUG

	bool "Enable/disable 0-4K memory initialization for QCA6174"

	depends on CNSS

	---help---

	  If enabled, 0-4K memory is reserved for QCA6174 to address

	  a MAC HW bug. MAC would do an invalid pointer fetch based on

	  the data, that was read from 0 to 4K. So fill it with zero's;

	  to an address for which PCIe root complex would honor the read

	  without any errors.

config CLD_DEBUG

	bool "Enable/disable CLD debug features"

	help

	 WLAN CLD driver uses this config to enable certain debug features.

	 Some of the debug features may affect performance or may compromise

	 on security.

	  Say N, if you are building a release kernel for production use.

	  Only say Y, if you are building a kernel with debug support.

config CLD_HL_SDIO_CORE

	tristate "Qualcomm Technologies Inc. Core wlan driver for QCA SDIO interface"

	select WIRELESS_EXT

	select WEXT_PRIV

	select WEXT_CORE

	select WEXT_SPY

	select NL80211_TESTMODE

	depends on ARCH_QCOM

	depends on MMC

config CLD_LL_CORE

	tristate "Qualcomm Technologies Inc. Core wlan driver"

	select NL80211_TESTMODE

	select WEXT_CORE

	select WEXT_PRIV

	select WEXT_SPY

	select WIRELESS_EXT

	---help---

	  This section contains the necessary modules needed to enable the

	  core WLAN driver for Qualcomm Technologies Inc QCA6174 chipset.

	  Select Y to compile the driver in order to have WLAN functionality

	  support.

config CNSS_SECURE_FW

	bool "Enable/Disable Memory Allocation for Secure Firmware Feature"

	depends on CNSS

	---help---

	  CLD Driver can use this for holding local copy of firmware

	  binaries which is used for sha crypto computation.

	  The Memory Allocation is done only if this Config Parameter is

	  enabled

config BUS_AUTO_SUSPEND

	bool "Enable/Disable Runtime PM support for PCIe based WLAN Drivers"

	depends on CNSS

	depends on PCI

	---help---

	  Runtime Power Management is supported for PCIe based WLAN Drivers.

	  The features enable cld wlan driver to suspend pcie bus when APPS

	  is awake based on the driver inactivity with the Firmware.

	  The Feature uses runtime power management framework from kernel to

	  track bus access clients and to synchronize the driver activity

	  during system pm.

	  This config flag controls the feature per target based. The feature

	  requires CNSS driver support.

source "drivers/net/wireless/cnss/logger/Kconfig"

config WLAN_FEATURE_RX_WAKELOCK

	bool "Enable RX wake lock feature"

	help

	Enable WLAN_FEATURE_HOLD_RX_WAKELOCK which is required to take rx

	wakelock when driver receives packets from fw.

# Makefile for CNSS platform driver

obj-$(CONFIG_CNSS_PCI)	+= cnss_pci.o

obj-$(CONFIG_CNSS_SDIO)	+= cnss_sdio.o

obj-$(CONFIG_CNSS)	+= cnss_common.o

obj-$(CONFIG_CNSS_LOGGER)	+= logger/