Merge "drivers: add a snapshot of various QPNP PMIC peripheral drivers" into msm-4.8

* msm-qpnp-pin

msm-qpnp-pin is a GPIO chip driver for the MSM SPMI implementation.

It creates a platform_device for every block of device_nodes.

These device_nodes contained within specify the PMIC pin number associated

with each gpio chip. The driver will map these to Linux GPIO numbers.

[PMIC GPIO Device Declarations]

-Root Node-

Required properties :

 - gpio-controller : Specify as gpio-contoller. All child nodes will belong to

   this gpio_chip.

 - #gpio-cells: We encode a PMIC pin number and a 32-bit flag field to

   specify the gpio configuration. This must be set to '2'.

 - #address-cells: Specify one address field. This must be set to '1'.

 - #size-cells: Specify one size-cell. This must be set to '1'.

 - compatible = "qcom,qpnp-pin" : Specify driver matching for this driver.

 - label: String giving the name for the gpio_chip device. This name

   should be unique on the system and portray the specifics of the device.

-Child Nodes-

Required properties :

 - reg : Specify the spmi offset and size for this pin device.

 - qcom,pin-num : Specify the PMIC pin number for this device.

Optional configuration properties :

 -  qcom,mode:		indicates whether the pin should be input, output, or

			both for gpios. mpp pins also support bidirectional,

			analog in, analog out and current sink.

			QPNP_PIN_MODE_DIG_IN	 = 0, (GPIO/MPP)

			QPNP_PIN_MODE_DIG_OUT	 = 1, (GPIO/MPP)

			QPNP_PIN_MODE_DIG_IN_OUT = 2, (GPIO/MPP)

			QPNP_PIN_MODE_ANA_PASS_THRU = 3, (GPIO_LV/GPIO_MV)

			QPNP_PIN_MODE_BIDIR	 = 3, (MPP)

			QPNP_PIN_MODE_AIN	 = 4, (MPP)

			QPNP_PIN_MODE_AOUT	 = 5, (MPP)

			QPNP_PIN_MODE_SINK	 = 6  (MPP)

 - qcom,output-type:	indicates gpio should be configured as CMOS or open

			drain.

			QPNP_PIN_OUT_BUF_CMOS		 = 0, (GPIO)

			QPNP_PIN_OUT_BUF_OPEN_DRAIN_NMOS = 1, (GPIO)

			QPNP_PIN_OUT_BUF_OPEN_DRAIN_PMOS = 2  (GPIO)

			QPNP_PIN_OUT_BUF_NO_DRIVE	 = 3, (GPIO_LV/GPIO_MV)

 - qcom,invert:		Invert the signal of the gpio line -

			QPNP_PIN_INVERT_DISABLE = 0 (GPIO/MPP)

			QPNP_PIN_INVERT_ENABLE	= 1 (GPIO/MPP)

 - qcom,pull:		This parameter should be programmed to different values

			depending on whether it's GPIO or MPP.

			For GPIO, it indicates whether a pull up or pull down

			should be applied. If a pullup is required the

			current strength needs to be specified.

			Current values of 30uA, 1.5uA, 31.5uA, 1.5uA with 30uA

			boost are supported. This value should be one of

			the QPNP_PIN_GPIO_PULL_*. Note that the hardware ignores

			this configuration if the GPIO is not set to input or

			output open-drain mode.

			QPNP_PIN_PULL_UP_30	 = 0, (GPIO)

			QPNP_PIN_PULL_UP_1P5	 = 1, (GPIO)

			QPNP_PIN_PULL_UP_31P5	 = 2, (GPIO)

			QPNP_PIN_PULL_UP_1P5_30  = 3, (GPIO)

			QPNP_PIN_PULL_DN	 = 4, (GPIO)

			QPNP_PIN_PULL_NO	 = 5  (GPIO)

			For MPP, it indicates whether a pullup should be

			applied for bidirectitional mode only. The hardware

			ignores the configuration when operating in other modes.

			This value should be one of the QPNP_PIN_MPP_PULL_*.

			QPNP_PIN_MPP_PULL_UP_0P6KOHM = 0, (MPP)

			QPNP_PIN_MPP_PULL_UP_OPEN    = 1  (MPP)

			QPNP_PIN_MPP_PULL_UP_10KOHM  = 2, (MPP)

			QPNP_PIN_MPP_PULL_UP_30KOHM  = 3, (MPP)

  - qcom,vin-sel:	specifies the voltage level when the output is set to 1.

			For an input gpio specifies the voltage level at which

			the input is interpreted as a logical 1.

			QPNP_PIN_VIN0 = 0, (GPIO/MPP/GPIO_LV/GPIO_MV)

			QPNP_PIN_VIN1 = 1, (GPIO/MPP/GPIO_MV)

			QPNP_PIN_VIN2 = 2, (GPIO/MPP)

			QPNP_PIN_VIN3 = 3, (GPIO/MPP)

			QPNP_PIN_VIN4 = 4, (GPIO/MPP)

			QPNP_PIN_VIN5 = 5, (GPIO/MPP)

			QPNP_PIN_VIN6 = 6, (GPIO/MPP)

			QPNP_PIN_VIN7 = 7  (GPIO/MPP)

  - qcom,out-strength:	the amount of current supplied for an output gpio.

			QPNP_PIN_OUT_STRENGTH_LOW  = 1  (GPIO)

			QPNP_PIN_OUT_STRENGTH_MED  = 2, (GPIO)

			QPNP_PIN_OUT_STRENGTH_HIGH = 3, (GPIO)

  - qcom,dtest-sel	Route the pin internally to a DTEST line.

			QPNP_PIN_DIG_IN_CTL_DTEST1 = 1	(GPIO/MPP)

			QPNP_PIN_DIG_IN_CTL_DTEST2 = 2,	(GPIO/MPP)

			QPNP_PIN_DIG_IN_CTL_DTEST3 = 3,	(GPIO/MPP)

			QPNP_PIN_DIG_IN_CTL_DTEST4 = 4,	(GPIO/MPP)

  - qcom,src-sel:	select a function for the pin. Certain pins

			can be paired (shorted) with each other. Some gpio pins

			can act as alternate functions.

			In the context of gpio, this acts as a source select.

			For mpps, this is an enable select.

			QPNP_PIN_SEL_FUNC_CONSTANT = 0, (GPIO/MPP)

			QPNP_PIN_SEL_FUNC_PAIRED   = 1, (GPIO/MPP)

			QPNP_PIN_SEL_FUNC_1	   = 2, (GPIO/MPP)

			QPNP_PIN_SEL_FUNC_2	   = 3, (GPIO/MPP)

			QPNP_PIN_SEL_DTEST1	   = 4, (GPIO/MPP)

			QPNP_PIN_SEL_DTEST2	   = 5, (GPIO/MPP)

			QPNP_PIN_SEL_DTEST3	   = 6, (GPIO/MPP)

			QPNP_PIN_SEL_DTEST4	   = 7  (GPIO/MPP)

			Below are the source-select values for GPIO_LV/MV.

			QPNP_PIN_LV_MV_SEL_FUNC_CONSTANT   = 0, (GPIO_LV/GPIO_MV)

			QPNP_PIN_LV_MV_SEL_FUNC_PAIRED	   = 1, (GPIO_LV/GPIO_MV)

			QPNP_PIN_LV_MV_SEL_FUNC_1	   = 2, (GPIO_LV/GPIO_MV)

			QPNP_PIN_LV_MV_SEL_FUNC_2	   = 3, (GPIO_LV/GPIO_MV)

			QPNP_PIN_LV_MV_SEL_FUNC_3	   = 4, (GPIO_LV/GPIO_MV)

			QPNP_PIN_LV_MV_SEL_FUNC_4	   = 5, (GPIO_LV/GPIO_MV)

			QPNP_PIN_LV_MV_SEL_DTEST1	   = 6  (GPIO_LV/GPIO_MV)

			QPNP_PIN_LV_MV_SEL_DTEST2	   = 7, (GPIO_LV/GPIO_MV)

			QPNP_PIN_LV_MV_SEL_DTEST3	   = 8, (GPIO_LV/GPIO_MV)

			QPNP_PIN_LV_MV_SEL_DTEST4	   = 9, (GPIO_LV/GPIO_MV)

 - qcom,master-en:	1 = Enable features within the

			pin block based on configurations. (GPIO/MPP)

			0 = Completely disable the block and

			let the pin float with high impedance

			regardless of other settings. (GPIO/MPP)

 - qcom,aout-ref:	set the analog output reference.

			QPNP_PIN_AOUT_1V25    = 0, (MPP)

			QPNP_PIN_AOUT_0V625   = 1, (MPP)

			QPNP_PIN_AOUT_0V3125  = 2, (MPP)

			QPNP_PIN_AOUT_MPP     = 3, (MPP)

			QPNP_PIN_AOUT_ABUS1   = 4, (MPP)

			QPNP_PIN_AOUT_ABUS2   = 5, (MPP)

			QPNP_PIN_AOUT_ABUS3   = 6, (MPP)

			QPNP_PIN_AOUT_ABUS4   = 7  (MPP)

 - qcom,ain-route:	Set the destination for analog input.

			QPNP_PIN_AIN_AMUX_CH5   = 0, (MPP)

			QPNP_PIN_AIN_AMUX_CH6   = 1, (MPP)

			QPNP_PIN_AIN_AMUX_CH7   = 2, (MPP)

			QPNP_PIN_AIN_AMUX_CH8   = 3, (MPP)

			QPNP_PIN_AIN_AMUX_ABUS1 = 4, (MPP)

			QPNP_PIN_AIN_AMUX_ABUS2 = 5, (MPP)

			QPNP_PIN_AIN_AMUX_ABUS3 = 6, (MPP)

			QPNP_PIN_AIN_AMUX_ABUS4 = 7  (MPP)

 - qcom,cs-out:		Set the the amount of output to sync in mA.

			QPNP_PIN_CS_OUT_5MA  = 0, (MPP)

			QPNP_PIN_CS_OUT_10MA = 1, (MPP)

			QPNP_PIN_CS_OUT_15MA = 2, (MPP)

			QPNP_PIN_CS_OUT_20MA = 3, (MPP)

			QPNP_PIN_CS_OUT_25MA = 4, (MPP)

			QPNP_PIN_CS_OUT_30MA = 5, (MPP)

			QPNP_PIN_CS_OUT_35MA = 6, (MPP)

			QPNP_PIN_CS_OUT_40MA = 7  (MPP)

 - qcom,apass-sel:	Set the ATEST channel to route the signal

			QPNP_PIN_APASS_SEL_ATEST1 = 0, (GPIO_LV/GPIO_MV)

			QPNP_PIN_APASS_SEL_ATEST2 = 1, (GPIO_LV/GPIO_MV)

			QPNP_PIN_APASS_SEL_ATEST3 = 2, (GPIO_LV/GPIO_MV)

			QPNP_PIN_APASS_SEL_ATEST4 = 3, (GPIO_LV/GPIO_MV)

*Note: If any of the configuration properties are not specified, then the

       qpnp-pin driver will not modify that respective configuration in

       hardware.

[PMIC GPIO clients]

Required properties :

 - gpios : Contains 3 fields of the form <&gpio_controller pmic_pin_num flags>

[Example]

qpnp: qcom,spmi@fc4c0000 {

		#address-cells = <1>;

		#size-cells = <0>;

		interrupt-controller;

		#interrupt-cells = <3>;

		qcom,pm8941@0 {

			reg = <0x0>;

			#address-cells = <1>;

			#size-cells = <1>;

			pm8941_gpios: gpios {

				compatible = "qcom,qpnp-pin";

				gpio-controller;

				#gpio-cells = <2>;

				#address-cells = <1>;

				#size-cells = <1>;

				gpio@c000 {

					reg = <0xc000 0x100>;

					qcom,pin-num = <62>;

				};

				gpio@c100 {

					reg = <0xc100 0x100>;

					qcom,pin-num = <20>;

					qcom,source_sel = <2>;

					qcom,pull = <5>;

				};

			};

			qcom,testgpio@1000 {

				compatible = "qcom,qpnp-testgpio";

				reg = <0x1000 0x1000>;

				gpios = <&pm8941_gpios 62 0x0 &pm8941_gpios 20 0x1>;

			};

		};

	};

};

Qualcomm Technologies, Inc. TADC Specific Bindings

TADC (Telemetry ADC) is a 10 bit resolution ADC which has 8 channels: battery

temperature, skin temperature, die temperature, battery current, battery

voltage, input current, input voltage, and OTG current.

=======================

Required Node Structure

=======================

A TADC must be described in two levels of devices nodes.

=======================

First Level Node - TADC

=======================

- reg

  Usage:      required

  Value type: <prop-encoded-array>

  Definition: Address and size of the TADC register block.

TADC specific properties:

- compatible

  Usage:      required

  Value type: <string>

  Definition: Must be "qcom,tadc".

- interrupts

  Usage:      required

  Value type: <prop-encoded-array>

  Definition: Peripheral interrupt specifier.

- interrupt-names

  Usage:      required

  Value type: <stringlist>

  Definition: Interrupt names.  This list must match up 1-to-1 with the

	      interrupts specified in the 'interrupts' property.

=============================================

Second Level Nodes - TADC Thermistor Channels

=============================================

- reg

  Usage:      required

  Value type: <u32>

  Definition: The 0 based channel number.

TADC thermistor channel specific properties:

- qcom,rbias

  Usage:      required

  Value type: <u32>

  Definition: The bias resistor value.

- qcom,therm-at-25degc

  Usage:      required

  Value type: <u32>

  Definition: The thermistor resistance at 25 DegC.

- qcom,beta-coefficient

  Usage:      required

  Value type: <u32>

  Definition: The beta coefficeent or B-parameter of the thermistor.

===============================================

Second Level Nodes - TADC Scale/Offset Channels

===============================================

- reg

  Usage:      required

  Value type: <u32>

  Definition: The 0 based channel number.

TADC scale/offset channel specific properties:

- qcom,scale

  Usage:      required

  Value type: <s32>

  Definition: The RAW scaling factor.

- qcom,offset

  Usage:      optional

  Value type: <s32>

  Definition: The offset after scaling.

=======

Example

=======

smb138x_tadc: qcom,tadc@3600 {

	compatible = "qcom,tadc";

	#address-cells = <1>;

	#size-cells = <0>;

	#io-channel-cells = <1>;

	interrupts = <0x36 0x0 IRQ_TYPE_EDGE_BOTH>;

	interrupt-names = "eoc";

	batt_temp@0 {

		reg = <0>;

		qcom,rbias = <68100>;

		qcom,rtherm-at-25degc = <68000>;

		qcom,beta-coefficient = <3450>;

	};

	skin_temp@1 {

		reg = <1>;

		qcom,rbias = <33000>;

		qcom,rtherm-at-25degc = <68000>;

		qcom,beta-coefficient = <3450>;

	};

	die_temp@2 {

		reg = <2>;

		qcom,scale = <(-1032)>;

		qcom,offset = <344125>;

	};

	batt_i@3 {

		reg = <3>;

		qcom,channel = <3>;

		qcom,scale = <20000000>;

	};

	batt_v@4 {

		reg = <4>;

		qcom,scale = <5000000>;

	};

	input_i@5 {

		reg = <5>;

		qcom,scale = <14285714>;

	};

	input_v@6 {

		reg = <6>;

		qcom,scale = <25000000>;

	};

	otg_i@7 {

		reg = <7>;

		qcom,scale = <5714286>;

	};

};

Qualcomm Technologies Inc. PNP v2 Flash LED

QPNP (Qualcomm Technologies Inc. Plug N Play) Flash LED (Light

Emitting Diode) driver v2 is used to provide illumination to

camera sensor when background light is dim to capture good

picture. It can also be used for flashlight/torch application.

It is part of PMIC on Qualcomm Technologies Inc. reference platforms.

Main node:

Required properties:

- compatible		: Should be "qcom,qpnp-flash-led-v2"

- reg			: Base address and size for flash LED modules

- qcom,pmic-revid	: phandle of PMIC revid module. This is used to

			  identify the PMIC subtype.

Optional properties:

- interrupts		: Specifies the interrupts associated with flash-led.

- interrupt-names	: Specify the interrupt names associated with interrupts.

- qcom,hdrm-auto-mode	: Boolean type to select headroom auto mode enabled or not

- qcom,isc-delay-us	: Integer type to specify short circuit delay. Valid values are 32, 64,

			  128, 192. Unit is uS.

- qcom,warmup-delay-us	: Integer type to specify warm up delay. Valid values are 32, 64,

			  128, 192. Unit is uS.

- qcom,short-circuit-det	: Boolean property which enables short circuit fault detection.

- qcom,open-circuit-det		: Boolean property which enables open circuit fault detection.

- qcom,vph-droop-det	: Boolean property which enables VPH droop detection.

- qcom,vph-droop-hys-mv	: Integer property to specify VPH droop hysteresis. It is only used if

			  qcom,vph-droop-det is specified. Valid values are 0, 25, 50 and 75.

			  Unit is mV.

- qcom,vph-droop-thresh-mv	: Integer property to specify VPH droop threshold. It is only used if

				  qcom,vph-droop-det is specified. Valid values are

				  2500 to 3200 with step size of 100. Unit is mV.

- qcom,vph-droop-debounce-us	: Integer property to specify VPH droop debounce time. It is only used

				  if qcom,vph-droop-det is specified. Valid values are 0, 8, 16 and 26.

				  Unit is uS.

- qcom,led1n2-iclamp-low-ma	: Integer property to specify current clamp low

				  level for mitigation. Unit is mA. Allowed

				  values are same as under qcom,max-current.

- qcom,led1n2-iclamp-mid-ma	: Integer property to specify current clamp mid

				  level for mitigation. Unit is mA. Allowed

				  values are same as under qcom,max-current.

- qcom,led3-iclamp-low-ma	: Integer property to specify current clamp low

				  level for mitigation. Unit is mA. Allowed

				  values are same as under qcom,max-current.

- qcom,led3-iclamp-mid-ma	: Integer property to specify current clamp mid

				  level for mitigation. Unit is mA. Allowed

				  values are same as under qcom,max-current.

- qcom,vled-max-uv		: Integer property for flash current predictive mitigation.

				  Default value is 3500000 uV.

- qcom,ibatt-ocp-threshold-ua	: Integer property for flash current predictive mitigation.

				  Default value is 4500000 uA.

- qcom,rparasitic-uohm		: Integer property for flash current predictive mitigation indicating

				  parasitic component of battery resistance. Default value is 0 uOhm.

- qcom,lmh-ocv-threshold-uv	: Required property for flash current preemptive LMH mitigation.

				  Default value is 3700000 uV.

- qcom,lmh-rbatt-threshold-uohm	: Required property for flash current preemptive LMH mitigation.

				  Default value is 400000 uOhm.

- qcom,lmh-mitigation-sel	: Optional property to configure flash current preemptive LMH mitigation.

				  Accepted values are:

				  0: MITIGATION_DISABLED

				  1: MITIGATION_BY_ILED_THRESHOLD

				  2: MITIGATION_BY_SW

				  Default value is 2.

- qcom,chgr-mitigation-sel	: Optional property to configure flash current preemptive charger mitigation.

				  Accepted values are:

				  0: MITIGATION_DISABLED

				  1: MITIGATION_BY_ILED_THRESHOLD

				  2: MITIGATION_BY_SW

				  Default value is 2.

- qcom,lmh-level		: Optional property to configure flash current preemptive LMH mitigation.

				  Accepted values are 0, 1, and 3. Default value is 0.

- qcom,iled-thrsh-ma		: Optional property to configure the led current threshold at which HW

				  preemptive mitigation is triggered. Unit is mA. Default value is 1000.

				  Accepted values are in the range 0 - 3100, with steps of 100.

				  0 disables autonomous HW mitigation.

- qcom,thermal-derate-en	: Boolean property to enable flash current thermal mitigation.

- qcom,thermal-derate-current	: Array of currrent limits for thermal mitigation. Required if

				  qcom,thermal-derate-en is specified. Unit is mA. Format is

				  qcom,thermal-derate-current = <OTST1_LIMIT, OTST2_LIMIT, OTST3_LIMIT>.

- qcom,otst-ramp-back-up-dis	: Boolean property to disable current ramp

				  backup after thermal derate trigger is

				  deasserted.

- qcom,thermal-derate-slow	: Integer property to specify slow ramping

				  down thermal rate. Unit is in uS. Allowed

				  values are: 128, 256, 512, 1024, 2048, 4096,

				  8192 and 314592.

- qcom,thermal-derate-fast	: Integer property to specify fast ramping

				  down thermal rate. Unit is in uS. Allowed

				  values are: 32, 64, 96, 128, 256, 384 and

				  512.

- qcom,thermal-debounce		: Integer property to specify thermal debounce

				  time. It is only used if qcom,thermal-derate-en

				  is specified. Unit is in uS. Allowed values

				  are: 0, 16, 32, 64.

- qcom,thermal-hysteresis	: Integer property to specify thermal derating

				  hysteresis. Unit is in deciDegC. It is only

				  used if qcom,thermal-derate-en is specified.

				  Allowed values are:

				  0, 15, 30, 45 for pmi8998.

				  0, 20, 40, 60 for pm660l.

- qcom,thermal-thrsh1		: Integer property to specify OTST1 threshold

				  for thermal mitigation. Unit is in Celsius.

				  Accepted values are:

				  85, 79, 73, 67, 109, 103, 97, 91.

- qcom,thermal-thrsh2		: Integer property to specify OTST2 threshold

				  for thermal mitigation. Unit is in Celsius.

				  Accepted values are:

				  110, 104, 98, 92, 134, 128, 122, 116.

- qcom,thermal-thrsh3		: Integer property to specify OTST3 threshold

				  for thermal mitigation. Unit is in Celsius.

				  Accepted values are:

				  125, 119, 113, 107, 149, 143, 137, 131.

- qcom,hw-strobe-option	: Integer type to specify hardware strobe option. Based on the specified

			  value, additional GPIO configuration may be required to provide strobing

			  support. Supported values are:

			  0: Flash strobe is used for LED1, LED2, LED3

			  1: Flash strobe is used for LED1, LED2 and GPIO10 is used for LED3

			  2: Flash strobe is used for LED1; GPIO9 is used for LED2; GPIO10 is used for LED3

- switchX-supply		: phandle of the regulator that needs to be used

				  as a supply for flash switch_X device.

Child node: Contains settings for each individual LED. Each LED channel needs a flash node and

torch node for itself, and an individual switch node to serve as an overall switch.

Required Properties:

- label			: Type of led that will be used, either "flash", "torch", or "switch.

- qcom,led-name		: Name of the LED.

- qcom,default-led-trigger	: Trigger for the camera flash and torch. Accepted values are

			  "flash0_trigger", "flash1_trigger", "flash2_trigger, "torch0_trigger",

			  "torch1_trigger", "torch2_trigger", and "switch_trigger".

- qcom,id		: ID for each physical LED equipped. In order to handle situation when

			  only 1 or 2 LEDs are installed, flash and torch nodes on LED channel 0

			  should be specified with ID 0; nodes on channel 1 be ID 1, etc. This is

			  not required for switch node.

- qcom,max-current	: Maximum current allowed on this LED. Valid values should be

			  integer from 0 to 1500 inclusive. Flash 2 should have maximum current of

			  750 per hardware requirement. Unit is mA. For torch, the maximum current

			  is clamped at 500 mA. This is not required for the switch node.

- qcom,duration-ms	: Required property for flash nodes but not needed for torch. Integer

			  type specifying flash duration. Values are from 10ms to 1280ms with

			  10ms resolution. This is not required for switch node.

- qcom,led-mask		: Required property for switch nodes. Bitmask to indicate which leds are

			  controlled by this switch node. Accepted values are in the range 1 to 7,

			  inclusive. Example:

			  qcom,led-mask = <4>; /* This switch node controls the flash2/torch2 led. */

Optional properties:

- qcom,current-ma	: operational current intensity for LED in mA. Accepted values are a

			  positive integer in the range of 0 to qcom,max-current inclusive.

- qcom,ires-ua		: Integer type to specify current resolution. Accepted values should be

			  12500, 10000, 7500, and 5000. Unit is uA.

- qcom,hdrm-voltage-mv	: Integer type specifying headroom voltage. Values are from 125mV to 500mV

			  with 25mV resolution. Default setting is 325mV

- qcom,hdrm-vol-hi-lo-win-mv	: Integer type to specify headroom voltage swing range. Values are

				  from 0mV to 375mV with 25mV resolution. Default setting is 100mV.

- pinctrl-names		: Name of the pinctrl configuration that will be used when external GPIOs

			  are used for enabling/disabling, HW strobing of flash LEDs. For more

			  information on using pinctrl, please refer

			  Documentation/devicetree/bindings/pinctrl/msm-pinctrl.txt

                          Following are the pinctrl configs that can be specified:

                          "led_enable" : pinctrl config to enable led. This should specify the active

                          configuration defined for each pin or pin group.

                          "led_disable" : pinctrl config to disable led. This should specify the sleep

                          configuration defined for each pin or pin group.

                          "strobe_enable" : pinctrl config to enable hw-strobe. This should specify the

                          active configuration defined for each pin or pin group.

                          "strobe_disable" : pinctrl config to disable hw-strobe. This should specify the

                          sleep configuration defined for each pin or pin group.

- qcom,hw-strobe-gpio	: phandle to specify GPIO for hardware strobing. This is used when there is no

			  pinctrl support or PMIC GPIOs are used.

- qcom,hw-strobe-sel	: Boolean property to enable hardware strobe. If not defined, software strobe

			  will be used.

- qcom,hw-strobe-edge-trigger	: Boolean property to select trigger type. If defined, hw-strobe is set to

				  be edge triggered. Otherwise, it is level triggered.

- qcom,hw-strobe-active-low	: Boolean property to select strobe signal polarity. If defined, hw-strobe

				  signal polarity is set to active-low, else it is active-high.

Example:

	qcom,leds@d300 {

		compatible = "qcom,qpnp-flash-led-v2";

		status = "okay";

		reg = <0xd300 0x100>;

		label = "flash";

		interrupts = <0x3 0xd3 0x0 IRQ_TYPE_EDGE_BOTH>,

			     <0x3 0xd3 0x1 IRQ_TYPE_EDGE_BOTH>,

			     <0x3 0xd3 0x2 IRQ_TYPE_EDGE_BOTH>,

			     <0x3 0xd3 0x3 IRQ_TYPE_EDGE_BOTH>,

			     <0x3 0xd3 0x4 IRQ_TYPE_EDGE_BOTH>,

			     <0x3 0xd3 0x5 IRQ_TYPE_EDGE_BOTH>,

			     <0x3 0xd3 0x6 IRQ_TYPE_EDGE_BOTH>,

			     <0x3 0xd3 0x7 IRQ_TYPE_EDGE_BOTH>;

		interrupt-names = "led-fault-irq",

				"mitigation-irq",

				"flash-timer-exp-irq",

				"all-ramp-down-done-irq",

				"all-ramp-up-done-irq",

				"led3-ramp-up-done-irq",

				"led2-ramp-up-done-irq",

				"led1-ramp-up-done-irq";

		qcom,hdrm-auto-mode;

		qcom,isc-delay = <192>;

		switch0-supply = <&pmi8998_bob>;

		pmi8998_flash0: qcom,flash_0 {

			label = "flash";

			qcom,led-name = "led:flash_0";

			qcom,max-current = <1500>;

			qcom,default-led-trigger =

						"flash0_trigger";

			qcom,id = <0>;

			qcom,current-ma = <1000>;

			qcom,duration-ms = <1280>;

			qcom,ires-ua = <12500>;

			qcom,hdrm-voltage-mv = <325>;

			qcom,hdrm-vol-hi-lo-win-mv = <100>;

		};

		pmi8998_flash1: qcom,flash_1 {

			label = "flash";

			qcom,led-name = "led:flash_1";

			qcom,max-current = <1500>;

			qcom,default-led-trigger =

						"flash1_trigger";

			qcom,id = <1>;

			qcom,current-ma = <1000>;

			qcom,duration-ms = <1280>;

			qcom,ires-ua = <12500>;

			qcom,hdrm-voltage-mv = <325>;

			qcom,hdrm-vol-hi-lo-win-mv = <100>;

		};

		pmi8998_flash2: qcom,flash_2 {

			label = "flash";

			qcom,led-name = "led:flash_2";

			qcom,max-current = <750>;

			qcom,default-led-trigger =

						"flash2_trigger";

			qcom,id = <2>;

			qcom,current-ma = <500>;

			qcom,duration-ms = <1280>;

			qcom,ires-ua = <12500>;

			qcom,hdrm-voltage-mv = <325>;

			qcom,hdrm-vol-hi-lo-win-mv = <100>;

			pinctrl-names = "led_enable","led_disable";

			pinctrl-0 = <&led_enable>;

			pinctrl-1 = <&led_disable>;

		};

		pmi8998_torch0: qcom,torch_0 {

			label = "torch";

			qcom,led-name = "led:torch_0";

			qcom,max-current = <500>;

			qcom,default-led-trigger =

						"torch0_trigger";

			qcom,id = <0>;

			qcom,current-ma = <300>;

			qcom,ires-ua = <12500>;

			qcom,hdrm-voltage-mv = <325>;

			qcom,hdrm-vol-hi-lo-win-mv = <100>;

		};

		pmi8998_torch1: qcom,torch_1 {

			label = "torch";

			qcom,led-name = "led:torch_1";

			qcom,max-current = <500>;

			qcom,default-led-trigger =

						"torch1_trigger";

			qcom,id = <1>;

			qcom,current-ma = <300>;

			qcom,ires-ua = <12500>;

			qcom,hdrm-voltage-mv = <325>;

			qcom,hdrm-vol-hi-lo-win-mv = <100>;

		};

		pmi8998_torch2: qcom,torch_2 {

			label = "torch";

			qcom,led-name = "led:torch_2";

			qcom,max-current = <500>;

			qcom,default-led-trigger =

						"torch2_trigger";

			qcom,id = <2>;

			qcom,current-ma = <300>;

			qcom,ires-ua = <12500>;

			qcom,hdrm-voltage-mv = <325>;

			qcom,hdrm-vol-hi-lo-win-mv = <100>;

			pinctrl-names = "led_enable","led_disable";

			pinctrl-0 = <&led_enable>;

			pinctrl-1 = <&led_disable>;

		};

		pmi8998_switch0: qcom,led_switch_0 {

			label = "switch";

			qcom,led-name = "led:switch_0";

			qcom,led-mask = <3>;

			qcom,default-led-trigger =

						"switch0_trigger";

		};

		pmi8998_switch1: qcom,led_switch_1 {

			label = "switch";

			qcom,led-name = "led:switch_1";

			qcom,led-mask = <4>;

			qcom,default-led-trigger =

						"switch1_trigger";

		};

	};